Specification Home
Products

Spray Sprinkler Bodies

Spray Nozzles

Rotors & Impacts

Valves & Valve Boxes

Controllers

Central Control

Drip

Drainage

Pumps & Filters

Industry Certified Products

Documentation

CAD & Drawings

Design Guides

Performance Charts

Design Resources

Pressure Loss Tables

Regulation

Training

Non-Potable Products

Features

Valve - 100PESBIVM
Filter type - Quick Check Basket Filter; 150 mesh (100 micron)
Flow Rate Capability (0.9 gph dripline with 12" emitter spacing) - 20 to 1300 ft (6 to 396m) of dripline
Valve box - Mini-Standard Rectangular
Warranty - 3yr Warranty
Controller compatibility -   
Compatible with traditionally-wired controllers   
Compatible with TBOS / DC controller when used with DC Latching solenoid
Compatible with IVM controllers (ESP-LXIVM/LXIVMP) when used with IVM SOL (shipped with this model)
Compatible with 2-wire decoder systems like ESP-LXD controller

Specifications

Operating flow range - 0.3 to 20.0 gpm; (1.13 to 75.7 l/m)
Min diagnostic flow - 3gpm
Inlet pressure - 15 to 150 psi; (1,0 to 10,3 bar)
Regulated pressure - 40 psi (2.8 bar)
Additional Specification Notes
* For flows below 5gpm Rain Bird recommends use of upstream filtration to prevent debris from collecting below the diaphragm

Dimensions

LxWxH - 14" Length
Inlet Size - 1" x 1"  NPT

Model Listing

XCZ100PRBLC

  • 1" Wide Flow Control Zone Kit for Light Commercial

    • XCZ100PRBCOM

  • 1" Wide Flow Control Zone Kit with Quick-Check Basket Filter

    • XCZ100PRBR

  • 1" Wide Flow Control Zone Kit (Non-Potable)

    • XCZ100IVMQ

  • 1" Wide Flow Control Zone Kit with IVM

    • Features

    Five-year trade warranty
    Water-lubricated, gear-driven pop-up rotor
    Top-serviceable rock screen
    Seal-A-Matic (SAM) check valve to help prevent low-head drainage
    Heavy-duty stainless steel retract spring ensures positive popdown
    Standard rubber black cover
    Available in non-reversing full-circle and 30-345° reversing part-circle. Full and part circle operation in one unit
    Optional opposing nozzle available
    Top serviceable for all required service

    Specifications

    Radius: 70 to 105 feet (21.3 to 32.0 m)
    Pressure: 60 to 100 psi (4.1 to 6.9 bar)
    Flow: 20 to 56 gpm (4.6 to 12.7 m3 /h or 76.5 to 211.6 l/m)
    1.5” ACME threaded inlet
    SAM check valve holds up to 5 feet (1.5 m) of head
    Available with 6x pre-installed nozzle combinations
    Nozzle outlet trajectory is 25°
    Options
    Sod Cup
    Green Rubber Cover - Synthetic Turf
    Purple Rubber Cover - Non-Potable

    Dimensions

    Exposed Diameter: 2.7” (6.9 cm)
    Overall Diameter: 5.25” (13.3 cm)
    Overall Height: 12.6” (32.0 cm)
    Pop-Up Height to Mid-Nozzle: 3.6” (9.1 cm)

    Model Listing

  • 11004: 1.5” ACME female-threaded inlet
  • 11004-ON: 1.5” ACME female-threaded inlet with opposing nozzle

    • Features

    Capacities of 4 to 8300 gpm
    Simple installation (no electrical power required)
    Efficient pre-filter to reduce sand load on downstream components
    Rain Bird Centrifugal Sand Separators are designed to separate abrasive particles before they can enter the irrigation system, keeping equipment clean and clear of debris, which minimizes the amount of maintenance required and increases operational efficiency
    The separator removes sand and particles that are heavier than water (materials with a specific gravity of 2 or greater)
    How It Works
    Liquids and solids enter the unit and begin traveling in a circular flow. This centrifugal action throws heavier particulates towards the filter walls and eventually downward in a spiral motion to the separation chamber. The particulates collect in the separation chamber and are purged manually from the system. The filtered water is then drawn to the separator’s vortex and through the outlet
    An optional automatic purge controller and valve can be used on all applications to automate the purge process, which eliminates the need for manual flushing. Small vertical design separators may be wall mounted or supported by the system piping

    Specifications

    image

    Model Listing

    Vertical Centrifugal Sand Separators

  • VCS-R5V: 0.5" Inlet Size
  • VCS-R7V: 0.75" Inlet Size
  • VCS-R10V: 1" Inlet Size
  • VCS-R12V: 1.25" Inlet Size
  • VCS-R15V: 1.5" Inlet Size
  • VCS-R20V: 2" Inlet Size
  • VCS-R25V: 2.5" Inlet Size
  • VCS-R30V: 3" Inlet Size
  • VCS-R40V: 4" Inlet Size

    • Angled Centrifugal Sand Separators

  • ACS-R40LA:  4" Inlet Size
  • ACS-R60LA: 6" Inlet Size
  • ACS-R80LA: 8" Inlet Size
  • ACS-R100LA: 10" Inlet Size
  • ACS-R120LA: 12" Inlet Size
  • ACS-R140LA: 14" Inlet Size
  • ACS-R160LA: 16" Inlet Size

    • Features

    Indicates when the Drip Irrigation Zone is Running
    Stem indicator pops up as a visual notification that water in the drip irrigation zone is running.
    Stem rises 6" (15 cm) with a colored indicator cap for clear visibility and notification. 
    When not in use, the stem retracts flush into the body to hide and protect the indicator. 
    Potable and Non-potable Indicator Options
    A yellow cap indicates that the water source in the drip irrigation zone is potable.
    A purple cap indicates that the water source in the drip irrigation zone is non-potable. 
    Durable Construction
    Constructed with UV resistant, high impact plastic. 
    Includes 16" of durable 1/4" distribution tubing. 
    Self piercing connection fitting pre-installed.

    Specifications

    Operating Range
    Pressure: 20 to 50 PSI (1,4 to 3,5 bar) 

    Model Listing

  • OPERIND: Drip System Operation Indicator

    • Features

    Best-in-Class Valves
    With industry-leading reliability and performance, the Rain Bird EFB-CP Series of commercial valves are now even better with preinstalled IVM-SOL
    Next Generation Two-Wire System
    The ESP-LXIVM Two-Wire Controller is the next leap forward—simplifying installation, improving reliability and enabling more troubleshooting features that save time
    Performance and Reliability
    With 50% fewer connections, an IVM Smart Valve is already 200% more reliable out of the box versus using a valve and decoder
    Features
    Reliable performance even in dirty water applications. Self-flushing filter resists debris build-up
    Rugged red brass construction for longer life
    Normally closed, reverse flow design ensures valve will fail in the closed position if a tear or rip in the diaphragm occurs. Prevents flooding, water waste and landscape damage
    Slow closing to prevent water hammer and subsequent system damage
    One-piece solenoid design with captured plunger and spring for easy servicing. Prevents loss of parts during field service
    Manual internal bleed operates the valve without allowing water into the valve box. Allows pressure regulator adjustment without turning on the controller
    Manual external bleed permits flushing debris from the system. Recommended for system start up and other repairs
    Contamination-proof, self-flushing filter screen resists debris build-up. Water flow continuously flushes the screen, dislodging particles and debris before they can accumulate and clog the filter
    Reclaimed water compatible: all models now feature EPDM diaphragms and chlorine-resistant parts as standard equipment
    Options (order separately)
    Accommodates optional, field installed PRS-D pressure regulating module to ensure optimum sprinkler performance
    Optional purple flow control handle for non-potable water applications: P/N 236927, IVMEFBHANB

    Specifications

    Pressure: 15 to 200 psi (1.04 to 13.80 bar)
    Flow with/without PRS-D: 5 to 200 GPM (1.14 to 45.40 m3/h; 0.32 to 12.60 l/s)
    Temperature: up to 150° F (66° C)
    Electrical Specifications
    Power: 26.5 Vrms 50/60 Hz (cycles/sec)
    Inrush current: <40mA (Peak)
    Quiescent current: <0.4mA (ave.)
    Voltage Range: 15.6 - 29.2 Vrms
    Compatible with LXIVM controllers
    Dimensions (H x L x W)
    IVM100EFB: 6" x 4½" x 3¼" (8.3 cm) x (15.2 cm) x (11.4 cm) H x L x W
    IVM150EFB: 6 ½" x 5½" x 4½" (11.4 cm) x (16.5 cm) x (14 cm) H x L x W
    IVM200EFB: 7" x 6¾" x 5¾" (14.6 cm) x (17.8 cm) x (17.1 cm) H x L x W

    Model Listing

  • IVM100EFB: 1" Brass Valve with IVM-SOL
  • IVM150EFB: 1½" Brass Valve with IVM-SOL
  • IVM200EFB: 2" Brass Valve with IVM-SOL

    • Features

    Provides worry free medium-flow rate filtered water quality
    Powered by source line water pressure, the filter’s backwashing system produces a concentrated high velocity and low volume reverse water flow to systematically clean the screen of any entrapped contaminants
    Models are available as a filter unit only, or as a filter assembly including bypass plumbing and valves for fast and easy installation on site
    Heavy-duty, durable, SS woven wire mesh screen filtration element with PVC support is supplied standard. Optional screen construction including multi-layer sintered SS and wedge wire are also available upon request. HT models only supplied with sintered SS
    Standard: 200 micron. Optional: 50 - 2000 micron. Flow rates will vary with screen size and water source. Max flow assumes good water quality (< 20 ppm solids) and 200 micron screen
    Standard flow rates from 100 to 2,640 GPM
    Standard maximum operating pressure of 150 PSI (higher pressures optionally available)
    Filtered, clean water backwashing initiated automatically by time or pressure differential via integrated Rain Bird F2 AC/DC Controller
    Flanged inlet and outlet standard except on HO-G-02 and HT-G-02 filter only configurations which are threaded. Grooved inlet and outlet configuration optionally available
    Vessel Material (based on model): Powder Coated Carbon Steel or 304 Stainless Steel, 316 SS and Duplex SS optional
    Available as filter only, or as a complete assembly with bypass manifold and valves. Higher pressures optionally available

    Specifications

    Filter
    Flow rate: 100-1320 gpm; higher flows available upon request
    Filter body: Powder Coated Carbon Steel or 304 stainless steel (depending on model)
    Fine screen: SS Mesh screen with PVC support or 316 SS sintered screen (depending on model), SS wedge wire slotted screen is also optionally available
    Optional bypass manifold: Powder coated carbon steel
    Filtration level: 120, 200 & 300 microns standard, others optional
    Inlet/Outlet connections: 2” NPT, 3”, 4”, 6”, 8” flanged
    Flush Valve: 1”, 1.5” or 2” depending on model
    Minimum operating pressure for flush operation: 35 psi
    Maximum operating pressure: 150 psi  (higher pressure options available)
    Automatic Controller
    Two stations plus master valve
    Input voltage: 110VAC, 50/60 Hz; 220 VAC optional
    Rust-proof outdoor enclosure
    Pressure differential, time, or manual backflush actuation
    Dimensions: 9.5” height x 7.8” width x 4” depth

    Model Listing

    Powder Coated Carbon Steel - Hydraulic Scanning Suction Filters

  • HO-G-02-LE-C-M: 2" Vertical Hydraulic Suction Scanner (Powder Coated Carbon Steel, filter only)
  • HO-G-03-LE-C-M: 3" Vertical Hydraulic Suction Scanner (Powder Coated Carbon Steel, filter only)
  • HO-G-04-LS-C-M: 4" Vertical Hydraulic Suction Scanner (Powder Coated Carbon Steel, filter only)
  • HO-G-04-LE-C-M: 4" Vertical Hydraulic Suction Scanner (Powder Coated Carbon Steel, filter only)
  • HO-G-06-LS-C-M: 6" Vertical Hydraulic Suction Scanner (Powder Coated Carbon Steel, filter only)
  • HO-G-08-LS-C-M: 8" Vertical Hydraulic Suction Scanner (Powder Coated Carbon Steel, filter only)
  • HO-G-08-LE-C-M: 8" Vertical Hydraulic Suction Scanner (Powder Coated Carbon Steel, filter only)

    • Stainless Steel - Hydraulic Scanning Suction Filters

  • HT-G-02-LE-S-M: 2" Vertical Hydraulic Suction Scanner (Stainless Steel, filter only)
  • HT-G-02-LEX-S-M: 2" Vertical Hydraulic Suction Scanner (Stainless Steel, filter only)
  • HT-G-03-LE-S-M: 3" Vertical Hydraulic Suction Scanner (Stainless Steel, filter only)
  • HT-G-04-LS-S-M: 4" Vertical Hydraulic Suction Scanner (Stainless Steel, filter only)
  • HT-G-04-LE-S-M: 4" Vertical Hydraulic Suction Scanner (Stainless Steel, filter only)

    • Powder Coated Stainless Steel - Hydraulic Scanning Suction Filters

  • HO-G-02-LE-S-M: 2" Vertical Hydraulic Suction Scanner (Stainless Steel, filter only)
  • HO-G-03-LE-S-M: 3" Vertical Hydraulic Suction Scanner (Stainless Steel, filter only)
  • HO-G-04-LS-S-M: 4" Vertical Hydraulic Suction Scanner (Stainless Steel, filter only)
  • HO-G-04-LE-S-M: 4" Vertical Hydraulic Suction Scanner (Stainless Steel, filter only)
  • HO-G-06-LS-S-M: 6" Vertical Hydraulic Suction Scanner (Stainless Steel, filter only)
  • HO-G-08-LS-S-M: 8" Vertical Hydraulic Suction Scanner (Stainless Steel, filter only)
  • HO-G-08-LE-S-M: 8" Vertical Hydraulic Suction Scanner (Stainless Steel, filter only)

    • Features

    Automatic self-cleaning disc filtration equipment with 2" valves and high density polyethylene manifolds  
    Ideal for surface and well water containing both organic (algae) and inorganic materials: rivers, reservoirs, canals, waste water, and well water containing light sand (<3PPM) and other contaminants
    The patented system's helical action provides efficient cleaning  
    Manufactured from engineered plastics to resist rust and corrosion from chemicals and water  
    All units are factory tested prior to shipment  
    Disc elements provide depth filtration -not just surface filtration  
    Unit is pre-assembled with HDPE (High –density polyethylene) manifold for easy installation  
    DP, time or manual backflush cycle can be imitated from the controller    
    Plastic backflush valves are lightweight and corrosion resistant  
    Low maintenance and performs reliable backflush  
    Filtration disc versatility (filtration grades can be easily changed)  
    Available with 100, 130, 200 or 400 micron discs (specify when ordering)
    Rain Bird HDF Series 1X2 filter backwash
    FILTRATION STAGE: As water goes through the discs, particles are projected away due to the cyclone effect, reducing the backflushing frequency  
    BACKFLUSHING STAGE: Water is projected through the discs, expelling the retained particles and evacuating them through the drainage manifold while the rest of the equipment is still in the filtration stage, supplying the remaining installation
    Rain Bird HDF Series-2 systems backwashes one station at a time while the remaining elements continue filtering
    FILTRATION STAGE: As water goes through the discs, particles are projected away and kept in suspension due to the cyclone effect, reducing the backflushing frequency  
    BACKFLUSHING STAGE: Water is projected through the discs, expelling the retained particles and evacuating them through the drainage manifold. The rest of the filters battery continue filtering. The filtration process restarts when the discs recompress. The backflush process is controlled by the Rain Bird Control Unit

    Specifications

    HDF Series 1x2 Disc Filters
    Suited for areas with or without electricity  
    Ideal where manual cleaning is troublesome  
    Compact design fits in tight spaces  
    Control Unit functions on pressure differential or time  
    Automatic self-cleaning 2” filter for low flow ranges  
    Maximum Flow: 106 gpm (24 m³/h)  
    Maximum filtering surface: (231 in²/1492 cm²)  
    Maximum pressure: 145 psi (10 bar)  
    Maximum temperature: 140°F (60°C)  
    Standard 100 micron: Optional 130, 200 or 400 micron
    HDF Series 2 Disc Filters
    Suitable for surface and well waters containing both organic (algae) and inorganic materials:  Rivers, reservoirs, canals and waste water  
    Well water containing light sand (<3 PPM) and other contaminants  
    Maximum flow: 845 gpm (192 m³/h)  
    Maximum filtering surface: (231 in²/1492 cm²)  
    Maximum pressure: 145 psi (10 bar)  
    Maximum temperature: 140°F (60°C)  
    Standard: 100 micron. Optional: 20, 50, 130, 200, or 400 micron
    Control Units
    Rain Bird Filtron 110 allows backwash activation by time or pressure differential. Controllers are available in 12 VDC, 110 VAC and 220 VAC.

    Model Listing

    HDF 1X2 Disc Filter

  • 1X2/2G: 1  x  2" filters, 2" NPT Connections

    • HDF Series 2 Disc Filters

  • 2x2/3G: 2  x  2" filters, 3" Grooved HDPE Manifold  
  • 3x2/4G: 3  x  2" filters, 4" Grooved HDPE Manifold  
  • 4x2/6G: 4  x  2" filters, 6" Grooved HDPE Manifold  
  • 5x2/6G: 5  x  2" filters, 6" Grooved HDPE Manifold  
  • 6x2/6G: 6  x  2" filters, 6" Grooved HDPE Manifold  
  • 7x2/6G: 7  x  2" filters, 6" Grooved HDPE Manifold  
  • 8x2/8G: 8  x  2" filters, 8" Grooved HDPE Manifold

    • HDF Series 4 Disc Filters

  • HDF 4 x 4L/8F: 4  x  4" filters, 8" Flanged HDPE Manifold
  • HDF 5 x 4L/8F: 5  x  4" filters, 8" Flanged HDPE Manifold  
  • HDF 6 x 4L/10F: 6  x  4" filters, 10" Flanged HDPE Manifold  
  • HDF 7 x 4L/10F: 7  x  4" filters, 10" Flanged HDPE Manifold  
  • HDF 8 x 4L/10F: 8  x  4" filters, 10" Flanged HDPE Manifold  
  • HDF 9 x 4L/12F: 9  x  4" filters, 12" Flanged HDPE Manifold  
  • HDF 10 x 4L/12F: 10  x  4" filters, 12" Flanged HDPE Manifold  
  • HDF 11 x 4L/12F: 11  x  4" filters, 12" Flanged HDPE Manifold  
  • HDF 12 x 4L/12F: 12  x  4" filters, 12" Flanged HDPE Manifold

    • Features

    Heavy-duty, durable, 316 SS woven wire mesh screen filtration element with PVC support is supplied standard. Optional screen construction including multi-layer sintered 316 SS and wedgewire are also available upon request. HT models only supplied with sintered SS.  
    Perfect for 4” to 14” (DN 100 to DN 350) applications  
    Polyester powder coated carbon steel and Stainless Steel options  
    Horizontal Configuration  
    Effective hydraulically powered backwash  
    Low backflush volume  
    Easy maintenance access to the internal components of the filter is via a removable front cover with handles that are secured to the front end of the filter housing

    Specifications

    Flow Rate: 300 – 7,500 gpm  
    Max Temperature: 210° F  
    Single SS electric ball valve: for flushing operations standard .
    Screen opening: 50μ – 2000μ  
    Working pressure: 40 – 150 psi  
    Vessel Material (based on model): Powder Coated Carbon Steel or 304 Stainless Steel, 316 SS and Duplex SS optional  
    Available as filter only, or as a complete assembly with bypass manifold and valves. Higher pressures optionally available

    Model Listing

    Powder Coated Carbon Steel Models

  • HO-I-03-PS-C-M
  • HO-I-04-PS-C-M
  • HO-I-06-PS-C-M
  • HO-I-08-PM-C-M
  • HO-I-08-PS-C-M
  • HO-I-10-PS-C-M
  • HO-I-12-PS-C-M
  • HO-I-14-PS-C-M

    • Stainless Steel Models

  • HO-I-03-PS-S-M
  • HO-I-04-PS-S-M
  • HO-I-06-PS-S-M
  • HO-I-08-PM-S-M
  • HO-I-08-PS-S-M
  • HO-I-10-PS-S-M
  • HO-I-12-PS-S-M
  • HO-I-14-PS-S-M
  • HT-I-03-LP-S-M
  • HT-I-04-PE-S-M
  • HT-I-06-PE-S-M
  • HT-I-08-PS-S-M
  • HT-I-08-PE-S-M
  • HT-I-10-PE-S-M
  • HT-I-12-PS-S-M

    • Bypass Manifold Models

  • I-3-CS-T   
  • I-4-CS-F   
  • I-6-CS-F   
  • I-8-CS-F   
  • I-10-CS-F

    • Features

    Galvanized, Self-Cleaning Pump Suction Screen removes large trash and debris from water sources, saving time and money in energy, pumping efficiency and maintenance costs  
    All water must pass through the pump suction screen attached to the end of the pump suction line before entering the pump intake pipe. A small, side-stream from the pump discharge plumbing drives two spray bars that continually rotate, jetting water at the screen and blasting debris away  
    Heavy 12 mesh stainless steel screen increases your pump efficiency for many years to come

    Specifications

    Body: Galvanized Steel  
    Minimum Backwash Pressure: 22 psi  
    Recommended Backwash Pressure: 45 psi  
    Backwash Flow Rates: (PSS200 - PSS1000: 18 gpm); (PSS1400 - PSS400: 26 gpm)      
    Custom mesh sizes available: 4, 8, 18, and 24  
    Standard flanged connections – others adapters available upon request

    Model Listing

    PSS: Self Cleaning Pump Suction Screen - 12 Mesh

  • PSS200: 4" Line Inlet  
  • PSS400: 6" Line Inlet  
  • PSS600: 8" Line Inlet  
  • PSS800: 10" Line Inlet  
  • PSS1000: 10" Line Inlet  
  • PSS1400: 12" Line Inlet      
  • PSS1700: 12" Line Inlet  
  • PSS2000: 14" Line Inlet  
  • PSS2000: 16" Line Inlet  
  • PSS2400: 16" Line Inlet  
  • PSS3000: 16" Line Inlet  
  • PSS3500: 18" Line Inlet  
  • PSS4000: 18" Line Inlet

    • Features

    Subsurface aeration and irrigation prevents tree and shrub transplant shock
    Highest efficiency solution for tree irrigation - up to 95% emission uniformity with minimal wind, evaporation, or edge control losses
    Aesthetically designed subsurface bubbler contributes to a landscape’s natural appearance
    Locking grate at grade deters vandals
    Helps prevent shallow root growth and hardscape damage
    Aesthetically attractive below grade installation
    Self-contained and factory assembled units for assured reliability (10", 18" and 36" sizes)

    Specifications

    RWS Models
    4" (10.2 cm) retaining cap and vandal resistant locking grate tops a 36" (91.4 cm) semi-rigid mesh tube
    Factory installed swing assemblies (excluding RWS) with a 1401 (0.25 gpm; 0.95 l/m), 1402 (0.5 gpm; 1.9 l/m), or 1404 (1.00 gpm; 3.8 l/m) bubbler on a fixed riser makes connecting to lateral lines easy
    Options: Check valve to keep lines from draining (10 ft. min holdback)Sand sock for use in fine soils
    RWS - Mini Models
    4" (10.2 cm) retaining cap and vandal resistant locking grate tops a18" (45.7 cm) semi-rigid mesh tube
    Factory installed ½" spiral barb elbow with a 1401 or 1402 bubbler makes connecting to lateral lines easy
    Options: Check valve to keep lines from draining and sand sock for use in fine soils
    RWS - Supplemental Models
    2" (5.1 cm) snap-on cap and base cap enclose a 10" (25.4 cm) semi-rigid mesh tube
    Factory installed ½" spiral barb elbow with PCT or 1401 bubbler makes connecting to lateral lines easy
    Options: Check valve to keep lines from draining Sand sock for use in fine soils

    Dimensions

    RWS: 4" diameter x 36" length (10,2 cm x 91,4 cm)
    RWS-Mini: 4" diameter x 18" length (10,2 cm x 45,7 cm)
    RWS-Supplemental: 2" diameter, 10" length (5.1 cm x 25,4 cm)

    Model Listing

    RWS Models - 36” (91,4 cm) Tube & 4” (10,2 cm) Grate

  • RWS:  Root Watering System Basic, ready for customer-provided irrigation hardware
  • RWS-B-C-1401: 0.25 gpm (0,95 l/m) bubbler & check valve on riser, versatile swing assembly with 1/2” (15/21) M NPT inlet
  • RWS-B-1401: 0.25 gpm (0,95 l/m) bubbler on riser, versatile swing assembly with 1/2” (15/21) M NPT inlet
  • RWS-B-X-1401: 0.25 gpm (0,95 l/m) bubbler on riser, 18” (46 cm) open swing assembly with 1/2” (15/21) M NPT inlet
  • RWS-B-C-1402: 0.5 gpm (1,9 l/m) bubbler & check valve on riser, versatile swing assembly with 1/2” (15/21) M NPT inlet
  • RWS-B-1402: 0.5 gpm (1,9 l/m) bubbler on riser, 12” (30.5 cm) versatile swing assembly with 1/2” (15/21) M NPT inlet
  • RWS-B-C-1404: 1 gpm (3,8 l/m) bubbler & check valve on riser, versatile swing assembly with 1/2” (15/21) M NPT inlet

    • RWS Mini Models - 18” (45,7 cm) Tube & 4” (10,2 cm) Grate

  • RWS-M:  Mini Root Watering System Basic, ready for customer provided irrigation hardware
  • RWS-M-B-C-1401: 0.25 gpm (0,95 l/m) bubbler & check valve on riser, 1/2” (15/21) M NPT inlet spiral barb elbow
  • RWS-M-B-1401: 0.25 gpm (0,95 l/m) bubbler on riser, 1/2” (15/21) M NPT inlet spiral barb elbow
  • RWS-M-B-C-1402: 0.5 gpm (1,9 l/m) bubbler & check valve on riser, 1/2” (15/21) M NPT inlet spiral barb elbow
  • RWS-M-B-1402: 0.5 gpm (1,9 l/m) bubbler on riser, 1/2” (15/21) M NPT inlet spiral barb elbow

    • RWS Supplemental Models - 10” (25,4 cm) Tube & 2” (5.1 cm) snap-on cap and base

  • RWS-S-B-C-1401: 0.25 gpm (0,95 l/m) bubbler & check valve on riser, 1/2” (15/21) M NPT inlet spiral barb elbow
  • RWS-S-B-1401: 0.25 gpm (0,95 l/m) bubbler on riser, 1/2” (15/21) M NPT inlet spiral barb elbow

    • RWS Accessories (RWS and RWS-M only)

  • RWS-SOCK:  Root Watering System Sand Sock
  • RWS-GRATE-P:  4” (10,2 cm) Purple Grate for RWS & RWS-M

    • Features

    1/2" & 3/4" blank tubing extruded from polyethylene resin materials for consistent durability
    ½” and ¾” blank drip distribution tubing extruded from a proprietary blend of polyethylene resins
    Ultra protection from heat exposure and ultraviolet radiation
    Thicker tubing wall for added toughness and kink resistance
    Black jacket to blend in with landscapes
    Available in 250’ and 500’ coils
    Available with 3 different colored stripes to differentiate zones

    Specifications

    Operating Range
    Water: Up to 110°F (43.33° C)
    Ambient: Up to 125°F (51.7° C)
    Pressure: 0 to 60 psi (0 to 4.1 bar)
    Specifications – 700 Series (1/2”)
    Outside Diameter: 0.700” (17.8 mm)
    Inside Diameter: 0.590” (15 mm)
    Wall Thickness: 0.055” (1.4 mm)
    Tubing Color: Black
    Compatible with Rain Bird TLF 600 Series Fittings
    Specifications – 710 Series (1/2”)
    Outside Diameter: 0.710” (18 mm)
    Inside Diameter: 0.600” (15.2 mm)
    Wall Thickness: 0.055” (1.4 mm)
    Tubing Color: Black
    Compatible with Rain Bird TLF 600 Series Fittings
    Specifications – 940 Series (3/4”)
    Outside Diameter: 0.940” (23.9 mm)
    Inside Diameter: 0.820” (20.8 mm)
    Wall Thickness: 0.060” (1.5 mm)
    Tubing Color: Black
    Compatible with Rain Bird TLF 800 Series Fittings

    Model Listing

    UltraXP – 700 Series (1/2”)

  • UXP700250: No Stripe, 250 ft. (76m) coil
  • UXP700500: No Stripe, 500 ft. (152m) coil
  • UXP700G250: Green Stripe, 250 ft. (76m) coil
  • UXP700G500: Green Stripe, 500 ft. (152m) coil

    • UltraXP – 710 Series (1/2”)

  • UXP710250: No Stripe, 250 ft. (76m) coil
  • UXP710500: No Stripe, 500 ft. (152m) coil
  • UXP710G250: Green Stripe, 250 ft. (76m) coil
  • UXP710G500: Green Stripe, 500 ft. (152m) coil
  • UXP710P250: Purple Stripe, 250 ft. (76m) coil
  • UXP710P500: Purple Stripe, 500 ft. (152m) coil

    • UltraXP – 940 Series (3/4”)

  • UXP940G500: Green Stripe, 500 ft. (152m) coil
  • UXP940P500: Purple Stripe, 500 ft. (152m) coil

    • Features

    Complete kit is the simplest, smallest and most reliable Control Zone Kit for commercial applications between 0.3 and 20 gpm (1.13 and 76 l/m)
    Includes the reliable, proven PESB Valve which provides patented scrubbing action, making this kit ideal for commercial dirty water applications
    Includes the Pressure Regulating, Quick-Check Basket Filter that has a clear indicator which goes from green to red, telling you when to clean the filter. This reduces maintenance and takes the guesswork out of cleaning the filter. In addition, the threaded top makes it easy to remove and clean the stainless steel screen
    Basket Filter and Pressure Regulator have been combined for one smaller Pressure Regulating, Quick-Check Basket filter that is 24% smaller than the previous unit

    Specifications

    Operating Range
    Operating Flow Range**: 0.3 to 20.0 gpm (1.13 to 75.7 l/m)*
    Inlet Pressure: 15 to 150 psi (1,0 to 10,3 bar)
    Regulating Pressure: 40 psi (2,8 bar)
    Filtration:  XCZ-100-PRBLC: Basket Filter; 200 mesh (75 micron) XCZ-100-PRBR: Basket Filter; 200 mesh (75 micron) XCZ-100-PRBCOM: Quick-Check Basket Filter; 200 mesh (75 micron)
    Temperature: Up to 150º F (66º C)
    * For flows below 5gpm Rain Bird recommends use of upstream filtration to prevent debris from collecting below the diaphragm

    Model Listing

  • XCZ-100-PRB-COM: 1" Ball Valve with 1" PESB Valve and 1" Pressure Regulating (40 psi), Quick-Check Basket Filter
  • XCZ-100-PRBR: 1" PESBR Valve and 1" Pressure Regulating (40psi) Basket Filter

    • Replacement Screens

  • FLOW120M: (120 mesh/125 micron stainless steel screen)
  • FLOW150M: (150 mesh/100 micron stainless steel screen)
  • FLOW200M: (200 mesh/75 micron stainless steel screen)

    • Replacement Cap

  • QKCHKCAP: (Complete cap with body o-ring

    • Features

    1/2" & 3/4" blank tubing extruded from polyethylene resin materials for consistent durability
    1/2" tubing is now available in two different sizes: 0.600" I.D. X 0.700" O.D. and 0.615" I.D. X 0.705" O.D.
    UV-resistant for installations at or below grad
    Compact coils for easy storage and shipping

    Specifications

    Operating Range
    Pressure: 0 to 60 psi (0 to 4.1 bar)

    Model Listing

    XBS 700 - ½" Tubing Models - 600-700

  • Outside diameter: 0.700" (17.8 mm)
  • Inside diameter: 0.600" (15.2 mm)
  • Wall thickness: 0.050" (1.3 mm
  • XBS700G500: 1/2" tubing, 500 foot (152 m) coil

    • XBS - ½" Tubing Models

  • Outside diameter: 0.705" (18 mm)
  • Inside diameter: 0.615" (15.6 mm)
  • Wall thickness: 0.045" (1.2 mm)
  • XBS100: 1/2" tubing, 100 foot (30 m) coil
  • XBS500: 1/2" tubing, 500 foot (152 m) coil

    • XBS 940 - ¾" Tubing Models

  • Outside diameter: 0.940" (24 mm)
  • Inside diameter: 0.820" (21 mm)
  • Wall thickness: 0.060" (1.5 mm
  • XBS940G500: 3/4" tubing, 500 foot (152 m) coil
  • XBS940P500: 3/4" tubing, 500 foot (152 m) coil
  • Note: XBS 940 is also available in 100’ coils

    • Features

    Oversized wiper seal prevents leaks and protects internals from debris
    Rain Curtain™ nozzles deliver even distribution over the entire radius including large wind resistant droplets and gentle close-in watering resulting in greener turf using less water
    A history of proven performance and reliability tested in millions of installations
    Self-flushing arc adjustment port that prevents buildup of debris
    5 year trade warranty

    Specifications

    Precipitation rate: 0.20 to 1.50 in/hr (5 to 38 mm/h)
    Radius: 25 to 50 feet (7.6 to 15.2 m)
    Radius may be reduced up to 25% with radius reduction screw
    Pressure: 25 to 65 psi (1.7 to 4.5 bar)
    Flow Rate: 0.76 to 9.63 gpm (3.0 to 36.6 l/m; 0.17 to 2.19 m3/h)
    Reversing full- and part-circle adjustment from 40° - 360°
    Standard nozzle trajectory of 25°. Low angle nozzle trajectory of 10°. MPR nozzles varied nozzle trajectory between 12° - 25°.
    Optional Features
    Plus (+) Flow shutoff: “The Green Top.” Reduce downtime on jobs by flushing and nozzling rotors without running back and forth to the controller or valves
    PRS (R) with flow optimizer technology: The 45 psi pressure regulator lowers water bills, provides exact flow of each rotor, equalizes lateral lines, and eliminates misting and fogging
    SAM Seal-A-Matic™ check valve: holds up to 7 feet (2.1 m) of elevation change
    Stainless steel (SS) riser: helps deter vandalism on public turf areas (available on 4 and 6" models)
    Purple cover (NP) :for non-potable systems

    Dimensions

    Pop-up height: Shrub; 4" (10,2 cm); 6" (15,2 cm); 12" (30,5 cm)
    Overall body height: Shrub: 7 3/4" (19,7cm) 4": 7 3/8" (18, 5 cm); 6": 9 5/8" (24,5 cm); 12": 16 7/8" (42,9 cm)
    Exposed surface diameter: 1 5/8" (4,1 cm)

    Model Listing

    Shrub Models:

  • 5000SPCSAM: Shrub Part Circle SAM
  • 5000+SPCSAM: Shrub Plus Part Circle SAM
  • 5000+SPCSAMNP: Shrub Plus Part Circle SAM Non Potable
  • 5000+SPCSAMR: Shrub Plus PRS Part Circle SAM
  • 5000+SPCSAMRN: Shrub Plus PRS Part Circle SAM Non Potable

    • 4" Part Circle (adjustable from 40° –360°):

  • 5004PC: 4" Part Circle
  • 5004PC20: 4" Part Circle w/2.0 Nozzle
  • 5004PC30: 4" Part Circle w/3.0 Nozzle
  • 5004PCSAM: 4" Part Circle SAM
  • 5004PCSAM20: 4" Part Circle SAM w/2.0 Nozzle
  • 5004PCNP: 4" Part Circle Non Potable
  • 5004+PC: 4" Plus Part Circle
  • 5004+PC20: 4" Plus Part Circle w/2.0 Nozzle
  • 5004+PC30: 4" Plus Part Circle w/3.0 Nozzle
  • 5004+PCSAM: 4" Plus Part Circle SAM
  • 5004+PCR: 4" Plus Part Circle PRS
  • 5004+PCSAMR: 4" Plus Part Circle SAM PRS
  • 5004+PCSAMR20: 4" Plus Part Circle SAM PRS w/2.0 Nozzle
  • 5004+PCSAMR30: 4" Plus Part Circle SAM PRS w/3.0 Nozzle
  • 5004+PCSAMRNP: 4" Plus Part Circle SAM PRS Non Potable
  • 5004+PCSAMRSS: 4" Plus Part Circle SAM PRS Stainless Steel
  • 5004+PCSAMRNS: 4" Plus Part Circle SAM PRS Stainless Steel Non Potable

    • 4" Full Circle (360 degrees only):

  • 5004FC: 4" Full Circle
  • 5004+FC: 4" Plus Full Circle
  • 5004+FCSAM: 4" Plus Full Circle SAM
  • 5004+FCSAMR: 4" Plus Full Circle SAM PRS
  • 5004+FCSAMRSS: 4" Plus Full Circle Stainless Steel SAM PRS

    • 6" Part Circle (adjustable from 40° –360°):

  • 5006PC: 6" Part Circle
  • 5006PC30: 6" Part Circle w/ 3.0 Nozzle
  • 5006+PC: 6" Plus Part Circle
  • 5006+PCSAM: 6" Plus Part Circle SAM
  • 5006+PCSAMNP: 6" Plus Part Circle SAM Non Potable
  • 5006+PCSAMR: 6" Plus Part Circle SAM PRS
  • 5006+PCSAMRNP: 6" Plus Part Circle SAM PRS Non Potable
  • 5006+PCSAMRSS: 6" Plus Part Circle SAM PRS Stainless Steel
  • 5006+PCSAMRNS: 6" Plus Part Circle SAM PRS Stainless Steel Non Potable

    • 12" Part Circle (adjustable from 40° –360°):

  • 5012+PCSAMR: 12" Plus Part Circle SAM PRS
  • 5012+PCSAMRNP: 12" Plus Part Circle SAM PRS Non Potable

    • Features

    Vandal resistance, brass reinforced turret for increased side impact durability
    Memory Arc® returns the rotor to its original arc setting
    Non-strippable drive mechanism prevents damage from vandals
    Easy, wet, dry arc adjustment with slotted screwdriver through top of rotor from 50° to 330° part-circle, 360° non-reversing full-circle. Full and part circle operation in one unit
    Left and right side trips adjustable for ease of installation without turning the case and loosening the pipe connection
    SAM Seal-A-Matic check valve
    3-port, color-coded Rain Curtain nozzles for optimal long-range, midrange, and close-in watering
    5 year warranty

    Specifications

    Radius: 39 to 81 feet (11.9 to 24.7 m)
    Precipitation rate: 0.48 to 1.23 inches per hour (12 to 31 mm/h)
    Pressure: 50 to 100 psi (3.5 to 6.9 bar)
    Flow: 3.8 to 36.3 gpm (0.86 to 8.24 m3/h; 14.4 to 137.4 l/m)
    1" NPT or BSP female threaded inlet
    SAM Seal-A-Matic™ check valve holds up to 10 feet (3.1 m) of elevation change
    Nozzle outlet trajectory is 25º
    Rain Curtain™ Nozzles: Included with rotor, other sizes available upon request; 10-grey, 12-beige, 14-light green, 16-dark brown, 18-dark blue
    Optional Features:
    Stainless steel (SS) riser helps deter vandalism on public turf areas
    Purple cover (NP) for non-potable systems
    Optional Sod Cup

    Dimensions

    Exposed diameter: 1 7/8" (4,8 cm)
    Overall diameter: 3 1/8" (7,9 cm)
    Overall height: 10 1/8" (25,7 cm)
    Pop-up height: 5" (12,7 cm)
    Note: Pop-up height is measured from cover to the primary nozzle port. Overall body height is measured popped down

    Model Listing

  • 8005: 1" NPT female threaded inlet
  • 8005-NP: 1" NPT female threaded inlet; non-potable cover
  • 8005-SS: 1" NPT female threaded inlet; stainless steel
  • 8005-NP-SS: 1" NPT female threaded inlet; stainless steel and non-potable cover

    • Nozzle Kits:

  • B81610: Low Flow Kit
  • B81620: Standard Flow Kit
  • B81630: High Flow Kit

    • Features

    At-a-Glance Description

    • Variable Frequency Drive (VFD) provides a wide range of hydraulic coverage
    • Pump Start Relay included making station ready to accept controller signals
    • Aluminum Deck and Enclosure to stand up to the elements
    • Isolation Valve for maintenance and priming
    • Liquid filled suction and discharge gauges for fast set point setting and troubleshooting
    • Optional mounting bracket for Rain Bird Controllers

    Specifications

    Enclosures / External Connections

    • Marine grade aluminum enclosure and deck
    • Fused main power disconnect
    • Pump Control
      • Runs based on signal from irrigation controller, or from optional Flow Start Switch (for pressure boost or flooded suction applications only)
      • 24VAC Pump start relay included. Other optional voltages available.
      • 130°F temperature cutout switch

    Electrical Features

    • Incoming power: Single phase 208V, 220V, 230V AC or three phase 480V AC
    • TEFC Motor
    • UL-listed components
    • Energy efficient – Variable Frequency Drive (VFD) maintains constant pressure at varying flow demand.
      • Stainless steel pressure transducer
      • Red light for VFD alarms
      • Green pump running light
      • Pipe fill mode reducing pressure surge at pump start up
      • Programmable override pump speed
      • Loss of prime and pipe break alarm
      • Dead head shut down
      • Transducer loss shut down
    • Optional mounting bracket for Rain Bird controllers
      • Pre-drilled for ESP-Me, ESP-LXMe, and ESP-LXD Series Controllers. (Rain Bird controller sold separately)
      • Mounted inside or outside aluminum enclosure

        **Separate independent power feed required to power controller.

    Accessories

    • Surge Suppression Kit
      • Single Phase (208-230 VAC) p/n CLPSES1P
      • Three Phase (208-230 or 480 VAC) p/n CLPSES3P
    • Pump Start Relay
      • 6VDC p/n CLPPSR06DC
      • 12VDC p/n CLPPSR12DC
    • Boost or Flooded Suction Accessories
      • Flow Start Kit p/n CLPBSTSW
    • Suction Lift Accessories
      • Foot valve – 4” Vertical Flanged p/n CLPFTVLV4VF
      • Static inlet screen

     

    Features

    Ratcheting stem just like standard spray bodies
    3-port, color-coded Rain Curtain nozzles for optimal long range,midrange, and close-in watering
    SAM Seal-A-Matic check valve
    Heavy-duty, stainless steel retract spring ensures positive pop-down
    5 year warranty

    Specifications

    Precipitation Rate: 0.37 to 1.31 inches per hour (9 to 33 mm/h)
    Radius: 39 to 65 feet (11,9 to 19,8 m)
    Pressure: 30 to 90 psi (2,1 to 6,2 Bars)
    Flow: 2.9 to 21.7 GPM (0,66 to 4,93 m3/h; 0,18 to 1,37 l/s)
    Rain Curtain™ Nozzles: Included with rotor, other sizes available upon request; 10-grey, 12-beige, 14-light green, 16-dark brown, 18-dark blue
    1" (26/34) female NPT or BSP threaded inlet
    SAM check device holds up to 10 feet (3,1 m) of elevation change
    Nozzle outlet trajectory is 25°
    Optional Features:
    Stainless steel (SS) riser helps deter vandalism on public turf areas
    Purple cover (NP) for non-potable systems

    Dimensions

    Overall height: 8 1/2" (21,6 cm)
    Pop-up height: 4" (10,2 cm)
    Exposed surface diameter: 2" (5,1 cm)
    Note: Pop-up height measured from the cover to center of nozzle. Overall body height is measured popped down

    Model Listing

    4" Part Circle:

  • 6504-PC: Part-circle
  • 6504-PC-NP: Part-circle, non-potable cover
  • 6504-PC-SS: Part-circle, stainless steel
  • 6504-PC-SS-NP: Part-circle, stainless steel, non-potable cover

    • 4" Full Circle:

  • 6504-FC: Full-circle
  • 6504-FC-NP: Full-circle, non-potable cover
  • 6504-FC-SS: Full-circle, stainless steel
  • 6504-FC-SS-NP: Full-circle, stainless steel, non-potable cover

    • Nozzle Kits:

  • B81610: Low Flow Kit
  • B81620: Standard Flow Kit

    • Features

    The Ultimate Protection for both Potable and Non-Potable Markets
    The RD1800 Series has been built to withstand harsh operating conditions such as chemically treated recycled water (reclaimed / nonpotable), dirty water containing grit, debris, and other particulates, and high operating pressures common in commercial irrigation systems.
    Non-potable models add an extra level of defense against the chlorine and chemicals found in recycled water, and feature a purple seal with the international "Do Not Drink" symbol and warnings in English and Spanish
    Benefits
    Patented, Triple-Blade Wiper Seal precisely balances flushing, flow-by and debris protection to optimize performance and durability at pop-up and retraction. Precision-controlled flushing at pop-up and retraction clears debris, ensuring positive stem retraction
    Unique debris pockets hold grit in place, removing it from circulation and preventing long-term damage. Parts are resistant to corrosion in treated recycled water containing chlorine
    SAM PRS Models: Incorporates all RD1800 Series SAM and PRS features. Meets the needs of all spray areas, regardless of changing elevation or water pressures
    Flow-Shield™ Models: Provides low flow vertical water jet visible from +200’ line of sight when a nozzle has been removed
    Non-Potable Water Models: Provides an alternative to clip-on caps and molded purple covers. Easy-to-read English “DO NOT DRINK”, Spanish “NO BEBA” warnings, and international 'Do Not Drink' symbol

    Specifications

    Spacing: 2.5 to 24 feet (0.8 to 7.3 m)
    Pressure: 15 to 100 psi (1.0 to 6.9 bar)
    SAM capability: Holds up to 14 feet (4.2 m) of head; 6 psi (0.3 bar)
    Flow-by SAM Models: 0 at 15 psi (1.0 bar) or greater; 0.5 gpm (0.1 m³/h; 0.03 l/s)
    Flow-by All Other Models: 0 at 10 psi (0.7 bar) or greater; 0.5 gpm (0.1 m³/h; 0.03 l/s)
    SAM-PRS models regulate nozzle pressure to an average 30 or 45 psi (2.1 or 3.1 bar) with inlet pressures of up to 100 psi (6.9 bar)
    Side inlets featured on non Seal-A-Matic™ (SAM) models only
    Five-year trade warranty

    Dimensions

    ½" (15/21) NPT female threaded inlet

    How to Specify

    RD1800 How To Specify

    Model Listing

    Base Models:

  • RD04-NP: 4" (10cm) pop-up height, Non-Potable
  • RD12-NP: 12" (30.5cm) pop-up height, Non-Potable

    • SAM PRS-30 Models:

  • RD04-S-P-30-NP: 4" (10cm) pop-up height, Non-potable
  • RD06-S-P-30-NP: 6" (15cm) pop-up height, Non-potable
  • RD12-S-P-30-NP: 12" (30.5cm) pop-up height, Non-potable

    • SAM PRS-30 & Flow-Shield™ Models:

  • RD04-S-P-30-F: 4" (10cm) pop-up height
  • RD04-S-P-30-F-N: 4" (10cm) pop-up height, Non-potable
  • RD06-S-P-30-F: 6" (15cm) pop-up height
  • RD06-S-P-30-F-N: 6" (15cm), Non-potable
  • RD12-S-P-30-F: 12" (30.5cm) pop-up height
  • RD12-S-P-30-F-N: 12" (30.5cm), Non-potable

    • SAM PRS-45 Models:

  • RD04-S-P-45-NP: 4" (10cm) pop-up height, Non-potable
  • RD06-S-P-45-NP: 6" (15cm) pop-up height, Non-potable
  • RD12-S-P-45-NP: 12" (30.5cm) pop-up height, Non-potable

    • SAM PRS-45 & Flow-Shield™ Models:

  • RD04-S-P-45-F: 4" (10cm) pop-up height
  • RD04-S-P-45-F-N: 4" (10cm) pop-up height, Non-potable
  • RD06-S-P-45-F: 6" (15cm) pop-up height
  • RD06-S-P-45-F-N: 6" (15cm) pop-up height, Non-potable
  • RD12-S-P-45-F: 12" (30.5cm) pop-up height
  • RD12-S-P-45-F-N: 12" (30.5cm) pop-up height, Non-potable

    • Features

    Simple
    Rain Bird’s patent-pending 4.3 psi check valve technology keeps the dripline charged with water at all times, increasing uniformity of watering, and conserves water by eliminating the need to recharge the line at the beginning of each watering cycle
    XFS-CV Sub-Surface Dripline emitters are protected from root intrusion by Rain Bird’s patent-pending Copper Shield™ Technology resulting in a system that does not require maintenance or replacement of chemicals to prevent root intrusion
    Rain Bird’s low-profile emitter design reduces in-line pressure loss, allowing longer lateral runs, simplifying design and reducing installation time
    Variety of standard emitter flow rates, emitter spacing and coil lengths provide design flexibility for sub-surface and on-surface areas with or without elevation changes
    Through the use of a proprietary tubing material, the XFS-CV Dripline with heavy-duty check valve is the most flexible dripline tubing in the industry, making it the easiest dripline to design with and install
    Made with Recycled Content
    All Rain Bird XF Dripline (XFD, XFS, XFCV, XFS-CV) qualify for LEED credit 4.2 because they contain at least 20% Polyethylene post consumer recycled material by cost. These come in an assortment of coil sizes, flow rates and emitter spacing
    Reliable
    The pressure-compensating emitter design provides a consistent flow over the entire lateral length ensuring higher uniformity for increased reliability in the pressure range of 20 to 60 psi
    Durable
    Dual-layered tubing (copper over black) provides unmatched resistance to chemicals, algae growth and UV damage
    Grit Tolerant
    Rain Bird’s proprietary emitter design resists clogging by use of an extra wide flow path combined with a self-flushing action

    Specifications

    Operating Range
    Opening Pressure: 14.5 psi
    Pressure: 20 to 60 psi (1.38 to 4.14 bar)
    Flow rates: 0.4, 0.6 and 0.9 gph (1.6, 2.3 and 3.5 l/hr)
    Temperature:
    -Water: Up to 100°F (37.8° C)
    -Ambient: Up to 125°F (51.7° C)
    Required Filtration: 120 mesh
    Specifications
    12" & 18" (30.5 cm, 45.7 cm) spacing
    Available in 100', 250' and 500' (30.5 m, 76.2 m and 152.4 m) coils
    Coil Colors: Copper, purple, purple stripe
    Use with XF Dripline Insert Fittings

    Dimensions

    OD: 0.634" (16mm)
    ID: 0.536" (13.6mm);
    Thickness: 0.049" (1.2mm)

    Model Listing

    XFS-CV: Coil Color - Copper

  • XFS-CV-04-12-500: 0.4 gph(1.6l/h), 12”(30.5cm) spacing, 500’(152.4m)
  • XFS-CV-04-18-500: 0.4 gph(1.6l/h), 18”(45.7cm) spacing, 500’(152.4m)
  • XFS-CV-06-12-100: 0.6 gph(2.3I/h), 12"(30.5cm) spacing, 100'(30.5m)
  • XFS-CV-06-12-250: 0.6 gph(2.3I/h), 12"(30.5cm) spacing, 250'(76.2m)
  • XFS-CV-06-12-500: 0.6 gph(2.3I/h), 12"(30.5cm) spacing, 500'(152.4m)
  • XFS-CV-06-18-100: 0.6 gph(2.3I/h), 18"(45.7cm) spacing, 100'(30.5m)
  • XFS-CV-06-18-250: 0.6 gph(2.3I/h), 18"(45.7cm) spacing, 250'(76.2m)
  • XFS-CV-06-18-500: 0.6 gph(2.3I/h), 18"(45.7cm) spacing, 500'(152.4m)
  • XFS-CV-09-12-100: 0.9 gph(3.5I/h), 12"(30.5cm) spacing, 100'(30.5m)
  • XFS-CV-09-12-250: 0.9 gph(3.5I/h), 12"(30.5cm) spacing, 250'(76.2m)
  • XFS-CV-09-12-500: 0.9 gph(3.5I/h), 12"(30.5cm) spacing, 500'(152.4m)
  • XFS-CV-09-18-100: 0.9 gph(3.5I/h), 18"(45.7cm) spacing, 100'(30.5m)
  • XFS-CV-09-18-250: 0.9 gph(3.5I/h), 18"(45.7cm) spacing, 250'(76.2m)
  • XFS-CV-09-18-500: 0.9 gph(3.5I/h), 18"(45.7cm) spacing, 500'(152.4m)

    • XFS-CV: Coil Color - Purple

  • XFS-CVP-04-12-500: 0.4 gph(1.6l/h), 12”(30.5cm) spacing, 500’(152.4m)
  • XFS-CVP-04-18-500: 0.4 gph(1.6l/h), 18”(45.7cm) spacing, 500’(152.4m)
  • XFS-CVP-6-12-500: 0.6 gph(2.3I/h) , spacing 12"(30.5cm), 500'(152.4m)
  • XFS-CVP-6-18-500: 0.6 gph(2.3I/h), spacing 18"(45.7cm), 500'(152.4m)
  • XFS-CVP-9-12-500: 0.9 gph(3.5I/h), spacing 12"(30.5cm), 500'(152.4m)
  • XFS-CVP-9-18-500: 0.9 gph(3.5I/h), spacing 18"(45.7cm), 500'(152.4m)

    • XFS-CV: Coil Color - Purple Stripe

  • XFS-CVPS-04-12-500: 0.4 gph(1.6l/h), 12”(30.5cm) spacing, 500’(152.4m)
  • XFS-CVPS-04-18-500: 0.4 gph(1.6l/h), 18”(45.7cm) spacing, 500’(152.4m)
  • XFS-CVPS-6-12-500: 0.6 gph(2.3I/h) , spacing 12"(30.5cm), 500'(152.4m)
  • XFS-CVPS-6-18-500: 0.6 gph(2.3I/h), spacing 18"(45.7cm), 500'(152.4m)
  • XFS-CVPS-9-12-500: 0.9 gph(3.5I/h), spacing 12"(30.5cm), 500'(152.4m)
  • XFS-CVPS-9-18-500: 0.9 gph(3.5I/h), spacing 18"(45.7cm), 500'(152.4m)

    • Features

    Proven impact drive with straight-through flow for superior performance in dirty water
    Five standard trajectory and two low angle (LA) color-coded nozzles for matched precipitation and in a wide range of applications
    360° full-circle OR arc adjustable from 20° to 340°
    Side and combination ½” or ¾” bottom inlet for design flexibility (Maxi-Paw)
    3 year warranty

    Specifications

    Precipitation Rate: 0.28 to 1.21 inches per hour (7 to 31 mm/h)
    Radius: 22 to 45 feet (6,7 to 13,7 m)
    Radius with Radius Reduction Screw: 18 ft (5,4 m)
    Pressure: 25 to 60 psi (1,7 to 4,1 Bars)
    Flow: 1.5 to 8.4 GPM (0,34 to 1,91 m3/h; 0,9 to 0,53 l/s)
    Combination 1/2" (15/21) or 3/4" (20/27) FPT bottom inlet  1/2" (15/21) FPT side inlet
    Nozzles: 06-red; 07-black; 08-blue; 10-yellow; 12-beige
    Low angle (LA) nozzles: 07 LA-black; 10 LA-yellow
    Nozzle outlet trajectory is 23° for 06, 07, 08, 10, and 12 nozzles
    LA nozzle outlet trajectory is 11°
    Available Nozzles:
    Standard trajectory 06, 07, 08, 10, 12
    Low Angle 07LA, 10LA

    Dimensions

    Overall height: 9 3/10" (23,6 cm)
    Pop-up height: 3" (7,6 cm)
    Exposed surface diameter: 5" (12,7 cm)

    Model Listing

  • 2045A: Closed Case Pop Up Sprinkler
  • 2045A-NP: Closed Case Pop Up Sprinkler with Non-Potable Purple Cover
  • 2045A-SAM: Closed Case Pop Up Sprinkler with Seal-A-Matic Check Valve
  • 2045A-SAM-NP: Closed Case Pop Up Sprinkler with Seal-A-Matic Check Valve and Non-Potable Purple Cover
  • * For Nozzle Information see performance chart

    • Features

    Variable Frequency Drive (VFD)  
    Pump Start Relay included (24VAC/DC with surge protection)  
    Flow Switch included  
    Bladder Tank included  
    Marine-Grade Aluminum Enclosure and deck with an exhaust fan  
    Isolation Valves for easy maintenance  
    Auto-Off-Manual Switch provides the user full control and override capabilities  
    Available in single and three phase 208V, 220V, 230V, VAC and three phase 480V VAC configurations  
    Multiple options for boost, flooded suction, and suction lift applications (see options list)  
    External Fault / Alarm and Run lights
    Plumbing Configurations
    Inlet and discharge piping on opposite sides of the enclosure  
    ½" priming port  
    Mechanical Features
    Discharge and intake isolation valves  
    Liquid filled pressure gauges on intake and discharge piping  
    Rugged centrifugal pump

    Specifications

    24V AC/DC pump start relay included for optional remote control Autonomous controls with wake on low pressure and retire on low flow  
    Low flow rate is verified with a pressure test prior to retiring the pump to prevent frequent motor starts and extend equipment life  
    Power Requirement: Single or three phase 208V, 220V, 230V AC or three phase 480V AC  
    TEFC Motor  
    UL Listed QCZJ packaged pump system file E249335  
    UL Listed NITW control panel file E251596
    Options and Accessories
    Rain Bird automatic suction scanning filter  
    Surge Suppression Kit: Single phase (208V, 220V, or 230V AC); Three phase (208V, 220V, 230V or 480V AC)  
    Stainless steel piping to replace internal powder coated carbon steel piping  
    Environmental package, includes space heater and enclosure insulation  
    Passive intake strainer and foot valve assembly for suction lift applications  
    Self-cleaning inlet strainer and foot valve assembly for improved suction lift performance

    Model Listing

    3HP Models:

  • ACLP03ACC: Up to 140 GPM at 18 PSI or up to 30 GPM at 39 PSI  
  • ACLP03CAC: Up to 68 GPM at 32 PSI or up to 24 GPM at 41 PSI    

    • 5HP Models:

  • ACLP05BAC: Up to 190 GPM at 23 PSI or up to 100 GPM at 29 PSI  
  • ACLP05DAC: Up to 75 GPM at 49 PSI or up to 25 GPM at 61 PSI      
  • ACLP05EAC: Up to 160 GPM at 30 PSI or up to 40 GPM at 55 PSI  
  • ACLP05FAC: Up to 90 GPM at 55 PSI or up to 35 GPM at 71 PSI    

    • 7.5HP Models:

  • ACLP07GAC: Up to 220 GPM at 29 PSI or up to 110 GPM at 36 PSI  
  • ACLP07HAC: Up to 140 GPM at 54 PSI or up to 40 GPM at 65 PSI  
  • ACLP07JAC: Up to 85 GPM at 75 PSI or up to 30 GPM at 90 PSI    

    • 10HP Models:

  • ACLP10KAC: Up to 240 GPM at 45 PSI or up to 120 GPM at 54 PSI  
  • ACLP10LAC: Up to 160 GPM at 64 PSI or up to 40 GPM at 79 PSI  
  • ACLP10NAC: Up to 100 GPM at 89 PSI or up to 30 GPM at 114 PSI  

    • 15HP Models:

  • ACLP15OAC: Up to 300 GPM at 59 PSI or up to 140 GPM at 74 PSI  
  • ACLP15PAC: Up to 200 GPM at 79 PSI or up to 50 GPM at 102 PSI  
  • ACLP15RAC: Up to 340 GPM at 51 PSI or up to 80 GPM at 67 PSI  
  • ACLP15SAC: Up to 180 GPM at 77 PSI or up to 100 GPM at 96 PSI    

    • 20HP Models:

  • ACLP20TAC: Up to 300 GPM at 64 PSI or up to 140 GPM at 79 PSI  
  • ACLP20UAC: Up to 200 GPM at 88 PSI or up to 50 GPM at 110 PSI  
  • ACLP20VAC: Up to 360 GPM at 60 PSI or up to 80 GPM at 78 PSI  
  • ACLP20WAC: Up to 200 GPM at 83 PSI or up to 100 GPM at 112 PSI

    • Features

    The QF Dripline Header elbows rotate 360º and incorporate a protective ring — preventing damage and ensuring a proper seal
    The ring also provides leverage to make attaching the dripline easier
    The rotating barb manages trenching misalignment. Move left or right to accommodate the dripline – no need to re-trench
    Elbows utilize the same design as Rain Bird’s popular XFF Fitting requiring 50% less insertion force, and are compatible with the XFF Fittings Tool

    Specifications

    QF Header - 3/4"
    OD: 0.940" (23.9mm)
    ID: 0.820" (20.8mm)
    Wall Thickness: 0.060" (1.5mm)
    QF Header - 1"
    OD: 1.200" (30.5mm)
    ID: 1.060" (26.9mm)
    Wall Thickness: 0.070" (1.8mm)

    Model Listing

  • XQF7512100: XQF 3/4”(19mm) Dripline Header 12”(30.5cm) Spacing, 100’(30.5m) Coil
  • XQF7518100: XQF 3/4”(19mm) Dripline Header 18”(45.7cm) Spacing, 100’(30.5m) Coil
  • XQF1012100: XQF 1”(25.4mm) Dripline Header 12”(30.5cm) Spacing 100’(30.5m) Coil
  • XQF1018100: XQF 1”(25.4mm) Dripline Header 18”(45.7cm) Spacing 100’(30.5m) Coil
  • XQF101210P: XQF 1”(25.4mm) Dripline Header 12”(30.5cm) Spacing 100’(30.5m) Coil Purple
  • XQF101810P: XQF 1”(25.4mm) Dripline Header 18”(45.7cm) Spacing 100’(30.5m) Coil Purple

    • Features

    Cost effective – Standardized VFD driven pump system in enclosure delivers high performance with minimum investment  
    Low Profile – Compact aluminum enclosure with powder-coated skid and piping  
    Energy efficient – Variable Frequency Drive (VFD) maintains constant pressure at varying flow demand  
    Reliability – Simple, standard design, easy installation and maintenance  
    Mechanical Features
    Inlet Butterfly Isolation Valve  
    Discharge Butterfly Isolation Valve  
    Silent Check Valve  
    Enclosures / External Connections
    Marine-Grade Aluminum Enclosure  
    Polyester Powder-Coated Steel Deck and Piping  
    Thermostat and Fan on Mechanical Enclosure  
    Pump Control
    Pump Start Relay  
    VFD - Variable Frequency Drive for Control of Pressure  
    Display
    Monochrome Touch Screen Display

    Specifications

    LP Series – Horizontal End Suction - 1 Pump – Aluminum Enclosure
    Motor Size : (5 HP), ( 7.5 HP), (10 HP)
    Pump Type: Horizontal End Suction
    Power Requirement: (480/60/3 V/HZ/PH), (208-230/60/3 V/HZ/PH), (208-230/60/1 V/HZ/PH)
    Inlet Pressure Requirement: Suction Lift or Boost Applications
    Outlet Pressure:Up to 100 psi (6.9 bar)
    Outlet Flow: Up to 200 gpm (12.6 lps, 45.4 m3/h) 
    Inlet / Discharge Size: 3" flange fitting standard - 2" and 4" Flange fitting adapters available
    LP Series – Vertical Multistage – 1 Pump – Aluminum Enclosure
    Motor Size: (1 HP),  (1.5 HP), (2 HP), (5 HP), (7.5 HP) 
    Pump Type: Vertical Multistage
    Power Requirement: (480/60/3 V/HZ/PH), (208-230/60/3 V/HZ/PH), (208-230/60/1 V/HZ/PH)
    Inlet Pressure Requirement: Suction Lift or Boost Applications  
    Outlet Pressure: Up to 120 psi (8.3 bar)   
    Outlet Flow: Up to 90 gpm (5.7 lps, 20.4 m3/h)
    Discharge Size: 2" flange fitting standard - 3" and 4" adapters available

    Dimensions

    Concrete Slab Dimensions (min):  65" x 49" (165 cm x 125 cm)  
    Platform Skid Dimensions (min): 53" x 39.75" (135 cm x 101 cm)  
    LP Series – Horizontal End Suction - 1 Pump – Aluminum Enclosure Cabinet Height: (from slab) 35" (89 cm)  
    LP Series – Vertical Multistage – 1 Pump – Aluminum Enclosure Cabinet Height: (from slab) 35" (89 cm) or 47" (107 cm)

    Model Listing

  • Horizontal End Suction - LP Series: 5 to 10 HP; Up to 100 psi (6.9 bar); Up to 200 gpm (12.6 lps, 45.4 m3/h)   
  • Vertical Multistage - LP Series: 1 to 7.5 HP; Up to 120 psi (8.3 bar); Up to 0 gpm (5.7 lps, 20.4 m3/h)

    • Features

    Simple
    Rain Bird’s low-profile emitter design reduces in-line pressure loss, allowing longer lateral runs, simplifying design and reducing installation time
    Variety of emitter flow rates, emitter spacing and coil lengths provide design flexibility for either sub-surface turf or sub-surface shrub and groundcover applications
    Reliable
    XFS Sub-Surface Dripline emitters are protected from root intrusion by Rain Bird’s patent-pending Copper Shield™ Technology resulting in a system that does not require maintenance or replacement of chemicals to prevent root intrusion
    The pressure-compensating emitter design provides a consistent flow over the entire lateral length ensuring higher uniformity for increased reliability in the pressure range of 8.5 to 60 psi
    Durable
    Dual-layered tubing (copper over black) provides unmatched resistance to chemicals, algae growth and UV damage
    Grit Tolerant: Rain Bird’s proprietary emitter design resists clogging by use of an extra-wide flow path combined with a self-flushing action

    Specifications

    Operating Range
    Pressure: 8.5 to 60 psi (0.58 to 4.14 bar)
    Flow rates: 0.6 and 0.9 gph (2.3 l/hr and 3.5 l/hr)
    Temperature:
      -Water: Up to 100°F (37.8° C)
      -Ambient: Up to 125°F (51.7° C)
    Required Filtration: 120 mesh
    Specifications
    Available in a 500' (52.4 m) coil
    Coil Color: Copper
    Use with XF Dripline Insert Fittings

    Dimensions

    OD: 0.634" (16mm)
    ID: 0.536" (13.6mm)
    Thickness: 0.049" (1.2mm)

    Model Listing

    XFS - Coil Color: Copper

  • XFS-06-12-500: XFS, 0.6 gph(2.3I/h), 12"(30.5cm) spacing, 500'(152.4m)
  • XFS-06-18-500: XFS, 0.6 gph(2.3I/h), 18"(45.7cm) spacing, 500'(152.4m)
  • XFS-09-12-500: XFS, 0.9 gph(3.5I/h), 12"(30.5cm) spacing, 500'(152.4m)
  • XFS-09-18-500: XFS, 0.9 gph(3.5I/h), 18"(45.7cm) spacing, 500'(152.4m)

    • XFS - Coil Color: Purple

  • XFSP-06-12-500: XFSP, 0.6 gph(2.3I/h), 12"(30.5cm) spacing, 500'(152.4m)
  • XFSP-06-18-500: XFSP, 0.6 gph(2.3I/h), 18"(45.7cm) spacing, 500'(152.4m)
  • XFSP-09-12-500: XFSP, 0.9 gph(3.5I/h), 12"(30.5cm) spacing, 500'(152.4m)
  • XFSP-09-18-500: XFSP, 0.9 gph(3.5I/h), 18"(45.7cm) spacing, 500'(152.4m)

    • Features

    Reliability – Integrated Plug-n-Pump provide single source responsibility for the entire pumping system insuring trouble-free installation and operation  
    Energy efficient – Variable Frequency Drive (VFD) maintains constant pressure at varying flow demand  
    Easy Start-up – All stations are water-tested at the factory prior to shipment.
    Inlet and discharge isolation valves for easier mechanical serviceability
    Mechanical Features
    Inlet Butterfly Isolation Valve  
    Discharge Butterfly Isolation Valve  
    Silent Check Valve
    Pressure / Flow
    Stainless Steel Pressure Transducer  
    Flow Switch
    Enclosures / External Connections
    Polyester Powder Coated Steel Enclosure  
    Polyester Powder-Coated Steel Deck and Piping  
    Re-Prime Piping (Suction Lift only)  
    Thermostat and Fan on Mechanical Enclosure
    Pump Control
    Pump Start Relay  
    VFD - Variable Frequency Drive for Control of Pressure
    Display
    Monochrome Touch Screen Display  
    Optional Color Touch Screen Display with Remote Communication Capability

    Specifications

    D-Series – Horizontal End Suction – 1 Pump – Green Enclosure
    Motor Size: (5 HP), (7 ½ HP), (10 HP), (15 HP), (20 HP)
    Pump Type:Horizontal End Suction
    Power Requirement: (208-230/60/3 V/HZ/PH),  (230/60/1 V/HZ/PH) , (208/60/1 V/HZ/PH)
    Inlet Pressure Requirement: Suction Lift (up to 3 ft. lift), or Boost Applications
    Outlet Pressure: Up to 130 psi (9.0 bar)
    Outlet Flow: Up to 350 gpm (22.1 lps, 79.5 m3/h) 
    Inlet / Discharge: Size: 4" standard - 2", 3" and 6" adapters are external accessories
    D-Series – Vertical Multistage – 1 Pump – Green Enclosure
    Motor Size:  (3 HP), (5 HP), (7 ½ HP), (10 HP), (15 HP)  
    Pump Type: Vertical Multi-Stage
    Power Requirement: (208-230/60/3 V/HZ/PH), (208-230/60/1 V/HZ/PH)
    Inlet Pressure Requirement: Suction Lift or Boost Applications
    Outlet Pressure: Up to 120 psi (8.3 bar) 
    Outlet Flow: Up to 180 gpm (11.4 lps, 40.9 m3/h)
    Inlet / Discharge Size: 4" Standard - 2", 3", and 6" adapters available

    Dimensions

    Concrete Slab Dimensions (min): 90" x 48" (229 cm x 122 cm)
    Platform Skid Dimensions (min): 78" x 36" (198 cm x 91 cm)
    Cabinet Height (from slab): 52" (132 cm) or 64" (163 cm)

    Model Listing

  • Horizontal End Suction - 1 Pump - D Series: 5 to 20 HP; Up to 130 psi (9.0 bar); Up to 180 gpm (11.4 lps, 40.9 m3/h)
  • Vertical Multistage – 1 Pump – D Series: 3 to 15 HP; Up to 120 psi (8.3 bar); Up to 200 gpm (12.6 lps, 45.4 m3/h)

    • Features

    Designed for excellent retention on 1800 Series Spray Body covers  
    Purple plastic cover for easy identification of non-potable water system  
    Marked with “Do Not Drink!” warning in both English and Spanish  
    Snaps onto all 1800® Series Spray Body covers

    Specifications

    Model

    • 1800-NPCAP

    Model Listing

  • 1800-NP

    • Features

    Durable glass-filled nylon construction with fabric-reinforced rubber diaphragm for long life and reliable performance    
    Globe configuration  
    Normally closed, forward flow design  
    Slow closing to prevent water hammer and subsequent system damage  
    Low flow capability for a wide range of applications  
    One-piece solenoid design with captured plunger and spring for easy servicing. Prevents loss of parts during field service  
    Flow control handle adjusts water flows as needed  
    Manual internal bleed manually operates the valve without allowing water into the valve box; allows pressure regulator to be adjusted without turning the valve on at the controller first  
    Manual external bleed permits flushing debris from the system. Recommended for system start up and after repairs  
    Stainless steel studs molded into the body. Bonnet can be attached and removed more easily and more often without damaging threads  
    Nylon scrubber scrapes a stainless steel screen to clean and break down grit and plant material. Prevents debris build-up and clogging (PESB Series only)  
    Five-year trade warranty

    Specifications

    Pressure: 20 to 200 psi (1.4 to 13.8 bar)  
    Flow without PRS-D option: 0.25 to 300 GPM (0.06 to 68.1 m3/h; 0.02 to 18.90 l/s)  
    Flow with PRS-D option: 5 to 300 GPM (1.14 to 68.1 m3/h; 0.32 to 18.90 l/s)
    Temperature: Up to 150° F (66° C)  
    Power: 24VAC 50/60Hz (cycles/sec) solenoid power requirement  
    Inrush current: 0.41A (9.9VA) at 50/60Hz  
    Holding current: 0.14A (3.43VA) at 50/60Hz    
    Options
    Accommodates optional, field-installed PRS-D pressure regulating module to ensure optimum sprinkler performance Regulates up to 100 psi (6.9 bar)  
    Accepts latching solenoid for use with Rain Bird battery-operated controllers up to 150 psi (10.35 bar)  
    Compatible with ESP-LXD decoders  
    Optional purple flow control handle for non-potable water applications PEB-NP-HAN1 (1"); PEB-NP-HAN2 (1½" and 2")

    Dimensions

    100-PEB: 6½" x 4" x 4" – (16.5 cm) x (10.2 cm) x (10.2 cm) H x L x W 
    150-PEB: 8" x 6" x 6" – (20.3 cm) x (15.2 cm) x (15.2 cm) H x L x W 
    200-PEB: 8" x 6" x 6" – (20.3 cm) x (15.2 cm) x (15.2 cm) H x L x W
    300-PESB: 13 1/4" x 8" x 7" – (34.61 cm) x (20.32 cm) x (17.78 cm) H x L x W

    Model Listing

  • 100-PEB and 100-PESB: 1" NPT 
  • 150-PEB and 150-PESB: 1 1⁄2" NPT 
  • 200-PEB and 200-PESB: 2" NPT
  • 300-PESB: 3" NPT
  • Note: BSP threads available; specify when ordering

    • Features

    Extra flexible tubing for fast, easy installation
    Dual-layered tubing (brown over black or purple over black) provides unmatched resistance to chemicals, UV damage and algae growth
    Patented emitter design provides for increased reliability
    Longer lateral runs than competition
    Unique material offers significantly greater flexibility, allowing tighter turns with fewer elbows for easier installation
    Choice of flow rates, spacing and coil lengths provides design flexibility for a variety of non-turfgrass applications
    Use an Air/Vacuum Relief Valve Kit when installation is below soil (pg 147)

    Specifications

    Operating Range
    Pressure: 8.5 to 60 psi (0.58 to 4.1 bar)
    Flow rates: 0.6 gph and 0.9 gph (2.3 l/h and 3.5 l/h)
    Temperature: Water up to 100° F (37.8C); Ambient up to 125° F (51.7C)
    Required filtration: 120 mesh
    Specifications
    Outside diameter: 0.634" (16.1 mm)
    Inside diameter: 0.536" (13.6 mm)
    Wall thickness: 0.049" (1.2 mm)
    Spacing: 12" or 18"
    Lengths: 100', 250', and 500' coils
    Use with XF Dripline Insert Fittings or Rain Bird Easy Fit Compression Fittings

    Model Listing

    XFD - Coil Color: Copper

  • XFD-06-12-100: XFD, 0.6 gph(2.3I/h), 12"(30.5cm) spacing, 100'(30.5m)
  • XFD-06-12-250: XFD, 0.6 gph(2.3I/h), 12"(30.5cm) spacing, 250'(76.2m)
  • XFD-06-12-500: XFD, 0.6 gph(2.3I/h), 12"(30.5cm) spacing, 500'(152.4m)
  • XFD-06-18-100: XFD, 0.6 gph(2.3I/h), 18"(45.7cm) spacing, 100'(30.5m)
  • XFD-06-18-250: XFD, 0.6 gph(2.3I/h), 18"(45.7cm) spacing, 250'(76.2m)
  • XFD-06-18-500: XFD, 0.6 gph(2.3I/h), 18"(45.7cm) spacing, 500'(152.4m)
  • XFD-09-12-100: XFD, 0.9 gph(3.5I/h), 12"(30.5cm) spacing, 100'(30.5m)
  • XFD-09-12-250: XFD, 0.9 gph(3.5I/h), 12"(30.5cm) spacing, 250'(76.2m)
  • XFD-09-12-500: XFD, 0.9 gph(3.5I/h), 12"(30.5cm) spacing, 500'(152.4m)
  • XFD-09-18-100: XFD, 0.9 gph(3.5I/h), 18"(45.7cm) spacing, 100'(30.5m)
  • XFD-09-18-250: XFD, 0.9 gph(3.5I/h), 18"(45.7cm) spacing, 250'(76.2m)
  • XFD-09-18-500: XFD, 0.9 gph(3.5I/h), 18"(45.7cm) spacing, 500'(152.4m)

    • XFD - Coil Color: Purple

  • XFDP-06-12-500: XFDP, 0.6 gph(2.3I/h), 12"(30.5cm) spacing, 500'(152.4m)
  • XFDP-06-18-500: XFDP, 0.6 gph(2.3I/h), 18"(45.7cm) spacing, 500'(152.4m)
  • XFDP-09-12-500: XFDP, 0.9 gph(3.5I/h), 12"(30.5cm) spacing, 500'(152.4m)
  • XFDP-09-18-500: XFDP, 0.9 gph(3.5I/h), 18"(45.7cm) spacing, 500'(152.4m)

    • XFD - Coil Color: Purple Stripe

  • XFDPS-06-12-500: XFDPS, 0.6 gph(2.3I/h), 12"(30.5cm) spacing, 500'(152.4m)
  • XFDPS-06-18-500: XFDPS, 0.6 gph(2.3I/h), 18"(45.7cm) spacing, 500'(152.4m)
  • XFDPS-09-12-500: XFDPS, 0.9 gph(3.5I/h), 12"(30.5cm) spacing, 500'(152.4m)
  • XFDPS-09-18-500: XFDPS, 0.9 gph(3.5I/h), 18"(45.7cm) spacing, 500'(152.4m)

    • Features

    Plastic diaphragm and scrubber components molded of chlorine- and chemical-resistant plastic material  
    Durable glass-filled nylon construction for long life and heavy-duty performance at 200 psi (13,80 bars) pressure  
    Stainless steel studs molded into the body. Bonnet can be attached and removed easily without damaging threads  
    One-piece solenoid design with captured plunger and spring for easy servicing. Prevents loss of parts during field service  
    External bleed protects the solenoid ports from debris when system is flushed  
    Internal bleed operates the valve without allowing water into the valve box; allows pressure regulator to be adjusted without turning on the valve at the controller first  
    Slow closing to prevent water hammer and subsequent system damage  
    Scrubber mechanism scrapes stainless steel screen clean to break down grit and plant material  
    Purple flow control handle standard on PESB-R Series valves  
    Five-year trade warranty
    Options
    Accommodates optional, field installed PRS-D pressure regulating module to ensure optimum sprinkler performance. Regulates up to 100 psi (6.9 bar)  
    Accepts latching solenoid for use with Rain Bird battery-operated controllers up to 150 psi (10.35 bar)  
    Compatible with ESP-LXD decoders

    Specifications

    Pressure: 20 to 200 psi (1.38 to 13.80 bar)  
    Flow: 0.25 to 200 gpm (0.06 to 45.40 m3⁄h; 0.02 to 12.60 l/s)  
    Flow with PRS-Dial: 5 to 200 gpm (1.14 to 45.40 m3⁄h; 0.32 to 12.60 l/s)  
    Temperature: Up to 150° F (66° C)  
    Power: 24VAC 50/60Hz (cycles/sec) solenoid power requirement  
    Inrush current: 0.41A (9.9VA) at 50/60Hz  
    Holding current: 0.14A (3.43VA) at 50/60Hz  
    Solenoid coil resistance: 30-39 Ohms, nominal

    Dimensions

    100-PESB-R: 6 1⁄2" x 4" x 4" (16.5 cm) x (10.2 cm) x (10.2 cm) H x L x W    
    150-PESB-R: 8" x 6" x 6" (20.3 cm) x (15.2 cm) x (15.2 cm) H x L x W
    200-PESB-R: 8" x 6" x 6" (20.3 cm) x (15.2 cm) x (15.2 cm) H x L x W

    Model Listing

  • 100-PESB-R: 1" NPT  
  • 150-PESB-R: 1½" NPT  
  • 200-PESB-R: 2" NPT

    • Features

    Higher Flow, Less Friction
    An industry‐leading flow range of 20‐62 gpm gives you unmatched versatility for commercial drip and spray irrigation applications
    With the highest maximum flow rate available, you can cover large zones while using fewer kits, saving money on every job
    Engineered to minimize friction loss, these kits preserve your water pressure in systems with a prescribed minimum PSI
    Convenience That's Ready to Go
    Ready out of the box, the 1.5" Commercial Control Zone Kit saves you and your crew valuable installation time on every job
    An intelligent, compact design provides easier access for maintenance and allows you to fit two kits into a jumbo valve box
    Reliability That's Built In
    Pre‐assembled units help to prevent mistakes that can occur during assembly
    Designed with fewer components, each kit minimizes the connection points in your system making it less susceptible to stress cracks
    Reclaimed water models (XCZ-150-LCDR) are engineered with components and materials that stand up to harsh chemicals
    Backed by a 3-year trade warranty, you can install each kit with confidence

    Specifications

    Flow Range: 20 to 62 gpm (75.7 l/min to 234.69 l/min)
    Inlet Pressure: 15 to 115 psi (1.03 to 7.9 bar)
    Regulated Pressure: 40 psi (2.8 bar)
    Filtration: 120 mesh (130 micron)
    Water Temperature: 33° F up to 110° F (0.5° C to 43° C)
    Ambient Temperature: 33° F up to 125° F (0.5° C to 52° C)
    Valve Type:
    XCZ-150-LCS: 1.5" PEB
    XCZ-150-LCDR: 1.5" PESB-R
    Power: 24 VAC 50/60 Hz (cycles/sec) solenoid
    Inrush Current: 0.41A (9.84 VA) at 50/60Hz
    Holding Current: 0.14A (3.43VA) at 50/60Hz
    Coil Resistance: 30-39 Ohms
    Two-wire compatible with ESP-LXD Decoders

    Dimensions

    XCZ-150-LCS: 15 1/4 " L x 5 3/4" W x 9½" H
    XCZ-150-LCDR: 18 1/2" L x 5 3/4" W x 9½" H

    Model Listing

  • XCZ-150-LCS: 1½" (3.81 cm) Stainless Steel Screen Filter, 120 Mesh (130 Micron); Surface Area: 42 in2 (270 cm2)
  • XCZ-150-LCDR: 1½" (3.81 cm) Disc Filter, 120 Mesh (130 Micron); Surface Area: 48 in2 (310 cm2)

    • Replacement Filters:

  • LGFC120MD: Replacement Disk Filter
  • LGFC120MS: Replacement Screen Filter

    • Features

    Best-in-Class Valves
    With industry-leading reliability and performance, the Rain Bird PEB/PESB Series of commercial valves are now even better with preinstalled IVM-SOL
    Next Generation Two-Wire System
    The ESP-LXIVM Two-Wire Controller is the next leap forward—simplifying installation, improving reliability and enabling more troubleshooting features that save time
    Performance and Reliability
    With 50% fewer connections, an IVM Smart Valve is already 200% more reliable out of the box versus using a valve and decoder
    Features
    Body constructed of durable glass-filled nylon for long life and heavy-duty performance at 200 psi (13.80 bar) pressure
    Stainless steel studs molded into the body. Bonnet can be attached and removed more easily without damaging threads
    One-piece solenoid design with captured plunger and spring for easy servicing. Prevents loss of parts during field service
    External bleed protects the solenoid ports from debris when system is flushed
    Internal bleed operates the valve without allowing water into the valve box; allows pressure regulator to be adjusted without turning on the valve at the controller first
    Low flow operating capability (0.25 gpm; 0.06 m3/h; 1.2 l/m) for a wide range of applications. For flows below 5 gpm (1.14 m3⁄h; 19.2 l/m) or any Xerigation® application, install Rain Bird Y filter upstream
    Slow closing to prevent water hammer and subsequent system damage
    PESBIVM only: Scrubber scrapes its stainless steel screen clean to break down grit and plant material. Prevents debris build-up and clogging
    Options (order separately)
    Accommodates optional, field installed PRS-D pressure regulating module to ensure optimum sprinkler performance
    Optional purple flow control handles for non-potable water applications: PEB-NP-HAN1(1”) & PEB-NP-HAN2 (11⁄2” and 2”)

    Specifications

    Pressure: 20 to 200 psi (1.38 to 13.80 bar)
    Flow: 0.25 to 200 gpm (0.06 to 45.40 m3⁄h; 1.2 to 757 l/m)
    Flow with PRS-D: 5 to 200 gpm (1.14 to 45.40 m3⁄h; 19.2 to 757 l/m)
    Temperature: up to 150° F (66° C)
    Electrical Specifications
    Power: 26.5 Vrms 50/60 Hz (cycles/sec)
    Inrush current: <40mA (Peak)
    Quiescent current: <0.4mA (ave.)
    Voltage Range: 15.6 - 29.2 Vrms
    Compatible with LXIVM controllers
    Dimensions (H x L x W)
    100 - 6.5” (16.5 cm), 4” (10.2 cm), 4” (10.2 cm)
    150 - 8” (20.3 cm), 6” (15.2 cm), 6” (15.2 cm)
    200 - 8” (20.3 cm), 6” (15.2 cm), 6” (15.2 cm)

    Model Listing

  • 100PEBIVM & 100PESBIVM: 1" Valve with IVM-SOL
  • 150PEBIVM & 150PESBIVM: 1.5" Valve with IVM-SOL
  • 200PEBIVM & 200PESBIVM: 2" Valve with IVM-SOL

    • Features

    Quick install and fewer points of failure reducing your time on the job and callbacks
    Quick self-priming operation for lawn irrigation *All pumps must be primed (filling the cavity with water) before they are first operated
    Standard 2" Inlet reduces the need for additional pipe adapters and potential points of failure
    115/230 dual voltage motor for maximum flexibility
    Built tough in the USA using a majority of U.S. content
    Heavy-duty cast-iron construction
    Motor featuring capacitor assisted start up and 2 oversized self-lubricating ball bearings for quiet continuous operation
    Chemical and abrasion resistant fiberglass reinforced thermoplastic impeller
    Cool running motor is engineered for continuous operation in ambient temperatures up to 145 F (65c)
    Constructed with ease of maintenance in mind
    4 bolts remove the motor for easy maintenance without disconnecting piping
    Easy access drain plug

    Specifications

    Impeller: Fiberglass reinforced thermoplastic
    Flows To: 66 GPM (250 LPM)
    Inlet and Outlet: 2" FNPT suction port / 1½" FNPT discharge port
    One-year trade warranty
    Motor Specs
    Single Phase
    115/230 dual voltage motor
    60 Hertz
    3,540 RPM
    Max Amps: 230v: 9amps | 115v: 18amps
    Applications
    Well
    Buried Cistern
    Lake and Ditchwater
    Gravity-fed above ground water source
    Boosting municipal water source

    Model Listing

  • BPUMP1HP: 1HP Booster Pump
  • BPUMP1-5HP: 1.5HP Booster Pump
  • BPUMP2HP: 2HP Booster Pump

    • Features

    Reliable performance even in dirty water applications. Self-flushing filter resists debris build-up  
    Rugged red brass construction for longer life  
    Durable, fabric-reinforced diaphragm composed of EPDM, a rubber material which is chlorine and chemical resistant  
    Normally closed, reverse flow design ensures valve will fail in the closed position if a tear or rip in the diaphragm occurs. Prevents flooding, water waste and landscape damage  
    Slow closing to prevent water hammer and subsequent system damage  
    One-piece solenoid design with captured plunger and spring for easy servicing. Prevents loss of parts during field service  
    Manual internal bleed operates the valve without allowing water into the valve box. Allows pressure regulator adjustment without turning on the controller  
    Manual external bleed permits flushing debris from the system.Recommended for system start up and other repairs  
    Contamination-proof, self-flushing filter screen resists debris build-up. Water flow continuously flushes the screen, dislodging particles and debris before they can accumulate and clog the filter  
    Reclaimed water compatible: all models now feature EPDM diaphragms and chlorine-resistant parts as standard equipment  
    Three-year trade warranty

    Specifications

    Pressure: 15 to 200 psi (1.04 to 13.80 bar)  
    Flow with/without PRS-D: 5 to 200 GPM (1.14 to 45.40 m3/h; 0.32 to 12.60 l/s)  
    Temperature: up to 150° F (66° C)  
    Power: 24 VAC 50/60Hz (cycles/sec) solenoid power requirement  
    Inrush current: 0.21A (5.0 VA) at 50/60Hz  
    Holding current: 0.10A (2.4 VA) at 50/60Hz  
    Solenoid coil resistance: 45-55 Ohms (50 nominal)

    Dimensions

    100-EFB-CP: 6" x 4½" x 3¼" (8.3 cm) x (15.2 cm) x (11.4 cm) H x L x W   
    150-EFB-CP: 6 ½" x 5½" x 4½" (11.4 cm) x (16.5 cm) x (14 cm) H x L x W   
    200-EFB-CP: 7" x 6¾ " x 5¾" (14.6 cm) x (17.8 cm) x (17.1 cm) H x L x W

    Model Listing

  • 100-EFB-CP: 1"    
  • 150-EFB-CP: 1½"  
  • 200-EFB-CP: 2"

    • Features

    Unique hybrid construction featuring durable red brass body and glass filled nylon bonnet for long life at a value price  
    Normally closed, forward flow design  
    Slow closing to prevent water hammer and subsequent system damage  
    Robust solenoid provides dependable performance even during constant operation  
    Flow control handle adjusts water flows as needed and incorporates a brass thread insert for longer life  
    Manual internal bleed operates the valve without allowing water into the valve box. Allows pressure regulator adjustment without turning the valve on at the controller  
    Manual external bleed permits flushing debris from the system. Recommended for system start up and repairs  
    Highly efficient operation with extremely low pressure loss  
    Patented nylon scrubber scrapes a stainless steel screen to clean and break down grit and plant material. Prevents debris build-up and clogging  
    Three-year trade warranty
    Options
    Accommodates optional, field installed PRS-D pressure regulating module to ensure optimum sprinkler performance  
    Accepts latching solenoid for use with Rain Bird battery-operated controllers up to 10.35 bar  
    Compatible with ESP-LXD decoders

    Specifications

    Pressure: 20 to 200 psi (1.4 to 13.8 bar)  
    Flow with/without PRS-D option: 60 to 300 gpm (13.6 to 68.1 m3/h; 3.78 to 18.90 l/s)  
    Temperature: up to 140° F (60° C)  
    Power: 24 VAC 50/60 Hz (cycles/sec) solenoid  
    Inrush current: 0.41 A (9.8 VA) at 50/60Hz  
    Holding current: 0.14 A (3.43 VA) at 50/60Hz    
    Coil resistance: 30-39 Ohms, nominal

    Dimensions

    Height: 13 5/8" (34.61 cm)  
    Length: 8" (20.32 cm)   
    Width: 7" (17.78 cm)

    Model Listing

  • 300-BPES: 3" NPT

    • Features

    Optional locking cover on models 33-DLRC, 44-LRC, 5-LRC, 33-DNP, 44-NP, and 5-NP (use 2049 key to unlock). Metal cover on model 7 only  
    One-piece body design (models 3-RC, 5-RC and 7)  
    Two-piece body design for easy servicing (models 33-DRC, 44-LRC, 44-RC, 33-DNP, and 44-NP)  
    Strong corrosion-resistant stainless steel spring prevents leakage  
    Thermoplastic cover for durability  
    33-DNP, 44-NP, and 5-NP covers marked with "Do Not Drink!" warnings in English and Spanish  
    Three-year trade warranty

    Specifications

    Pressure: 5 to 125 psi (0.35 to 8.63 bar)  
    Flow: 10 to 125 gpm (2.27 to 28.38 m3⁄h; 37.8 to 473 l/m)  
    33-DNP, 44-NP, and 5-NP flow: 10 to 70 gpm (2.27 to 15.89 m3⁄h; 37.8 to 265 l/m)

    Dimensions

    3-RC: Height 4¼" (10.8 cm)  
    33-DRC: Height 4 3⁄8" (11.1 cm)  
    33-DLRC: Height 4 5⁄8" (11.7 cm)  
    44-RC: Height 6" (15.2 cm)  
    44-LRC: Height 6" (15.2 cm)  
    5-RC: Height 5½" (14.0 cm)  
    5-LRC: Height 5½" (14.0 cm)  
    7: Height 5¾" (14.6 cm)  
    33-DNP: Height 4 3/8" (11.1 cm)  
    44-NP: Height 6" (15/2 cm)  
    5-NP: Height 5½" (14.0 cm)
       

    Model Listing

  • 3-RC: ¾" NPT Rubber Cover, 1-Piece Body  
  • 33-DRC: ¾" NPT Double Track Key Lug, Rubber Cover, 2-Piece Body      
  • 33-DLRC: ¾" NPT Double Track Key Lug, Locking Rubber Cover, 2-Piece Body  
  • 44-RC: 1" NPT Rubber Cover, 2-Piece Body  
  • 44-LRC: 1" NPT Locking Rubber Cover, 2-Piece Body  
  • 5-RC: 1" NPT Rubber Cover, 1-Piece Body  
  • 5-RC-BSP: 1" BSP Rubber Cover, 1-Piece Body, BSP threaded  
  • 5-LRC-BSP: 1" BSP Locking Rubber Cover, 1-Piece Body, BSP threaded  
  • 7: 1½" NPT Metal Cover, 1-Piece Body

    • Non-Potable

  • 33-DNP: ¾" NPT Non-potable, Purple Locking Rubber Cover, 2-Piece Body  
  • 44-NP: 1" NPT Non-potable, Purple Locking Rubber Cover, 2-Piece Body  
  • 5-NP: 1" NPT Non-potable, Purple Locking Rubber Cover, 1-Piece Body

    • International

  • 33DK: Valve key ¾” male and ½” female threads  
  • 5LRC: 1” BSP female threaded inlet with locking rubber cover  
  • 55K-1: Valve key 1” BSP male threads

    • Features

    The PRS-Dial is an excellent means of regulating outlet pressure at the valve regardless of incoming pressure fluctuations. The visible scale makes adjustment quick and easy. The regulator fits all Rain Bird PGA, PEB, PESB, PESB-R, EFB-CP, and BPES series valves  
    Regulates and maintains constant outlet pressure between 15 and 100 psi (1.04 to 6.9 bar) within ±5 psi (±0.34 bar)  
    Ergonomic design with snap-tight cover to prevent vandalism    
    Waterproof dial cartridge eliminates fogging and binding  
    Dial cartridge retrofits into all existing PRS-D units  
    Schrader valve connects pressure hose gauge  
    Easy field installation. PRS-Dial threads underneath the solenoid and adapter    
    Corrosion-resistant glass-filled nylon for rugged performance
    Application Information
    Proper operation requires inlet pressure to be a minimum of 15 psi (1.04 bar) higher than desired outlet pressure  
    For areas with very high pressure or uneven terrain, install sprinklers with PRS pressure regulating stems and/or SAM check valves  
    When inlet pressure exceeds 100 psi (6.9 bar), a pressure regulating master valve or inline pressure regulator is required    
    Rain Bird does not recommend using the pressure regulating module for applications outside the recommended flow ranges  
    To reduce the effects of water hammer, Rain Bird recommends flow rates in the supply line not to exceed 7.5 ft/sec (2.29 m/s)  
    For flows below 10 gpm (2.27 m3/h; 37.8 l/m), Rain Bird recommends the flow control stem be turned down two full turns from the fully open position

    Specifications

    Pressure: Up to 100 psi (6.9 bar)  
    Regulation: 15 to 100 psi (1.04 to 6.9 bar)  
    Flow: Refer to Valve Flow Ranges chart

    Model Listing

  • PRS-D: Pressure Regulating Module

    • Features

    • Available in three models: 
      • 25,4 cm (10 in.) round valve box with snap-in lid
      • 30,5 cm (12 in.) rectangular valve box with snap-in lid
      • Irrigation hydrant with interlocking lid, built-in 19 mm (3/4 in.) male ball valve outlet and 19 mm (3/4 in.) female inlet
    • Provide rugged, no-nonsense dependability
    • Lightweight and durable black bodies prevent soil and other debris from entering the box
    • Green lids help blend into grass and foliage
    • Pre-molded slots provide quick and easy supply pipe placement
    • Bottom flanges to help prevent sinking in unstable ground
    • Black body and green cover constructed of polypropylene
    • Designed to provide tight seals and easy maintenance access

    Specifications

    Dimensions:

    • RNDVBA10 – 25.4 cm (10 in.) Round Valve Box 
      • Top opening diameter (nominal): 24,0 cm (9.4 in.)
      • Bottom opening diameter (nominal): 33,5 cm (13.2 in.)
      • Height (nominal): 25,5 cm (10.0 in.)
    • STDVBA – 30.5 cm (12 in.) Rectangular Valve Box
      • Length (nominal): 38,6 cm (15.2 in.)
      • Width (nominal): 37,0 cm (14.6 in.)
      • Height (nominal): 30,5 cm (12.0 in.)
    • RNDVBA34 – Round Irrigation Hydrant
      • Top opening diameter (nominal): 21,0 cm (8.3 in.)
      • Bottom opening diameter (nominal): 18,0 cm (7.1 in.)
      • Height (nominal): 12,0 cm (4.7 in.)
      • Male ball valve outlet: 19,0 mm (3/4 in.) 
      • Female inlet: 19,0 mm (3/4 in.) 

    Dimensions

    7 Inch Round Valve Box- Bottom Diameter: 8.4 inches (21.4 cm) x  Height: 9.2 inches (23.4 cm)
    10 Inch Round Valve Box- Bottom Diameter: 11.8 inches (30,0 cm) x  Height: 10.2 inches (26,0 cm)
    Standard Valve Box- Length: 23.2 inches (59.0 cm)  x Width: 19.3 inches (49.1cm)  x Height: 12.5 inches (31.8 cm)
    Standard Extension - Length: 20.0 inches (50.8 cm) x  Width: 14.75 inches (37.5 cm) x Height: 6.75 inches (17.1 cm)
    Jumbo Valve Box - Length: 27.6 inches (70,0 cm) x Width: 21.0 inches (53,2 cm) x  Height: 12.5 inches (31.6 cm)
    Jumbo Extension - Length: 24.4 inches (62.0 cm) x Width: 17.9 inches (45.5 cm) x Height: 6.75 inches (17.2 cm)
    Super Jumbo Valve Box - Length: 33.1 inches (84.1 cm) x Width: 23.9 inches (60.7 cm) x Height: 15.0 inches (38.1 cm)
    Maxi Jumbo Valve Box - Length: 40.4 inches (102.5 cm) x Width: 27.1 inches (68.9 cm) x Height: 18.0 inches (45.7 cm)

    Model Listing

    RNDVBA10 – 25.4 cm (10 in.) Round Valve Box

  • Lightweight and durable black body and snap-in green lid
  • Provides protection for manual or electric valves from damage
  • For use with one valve

    • STDVBA – 30.5 cm (12 in.) Rectangular Valve Box

  • Lightweight and durable black body and snap-in green lid
  • Provides protection for manual or electric valves from damage
  • For use with up to four valves

    • RNDVBA34 – Round Irrigation Hydrant

  • Lightweight and durable black body and interlocking green lid
  • Built-in 19 mm (3/4 in.) male ball valve outlet and 19 mm (3/4 in.) female inlet
  • Ideal for connecting hoses or other irrigation products to a water source

    • Features

    Cap snaps securely onto the PC Module and XB emitter outlet to create bubbler effect and prevent wash out
    Designed for quick and easy installation
    Made of UV-resistant polyethylene material

    Model Listing

  • PC-DIFFUSER: Black diffuser cap
  • PC-DIFF-PPL: Purple diffuser cap to designate non-potable water

    • Features

    Strength and Stability – Multiple sizes and shapes are designed with corrugated sides and wide flange bases for maximum durability, compression strength, and stability  
    Smart Lid Design – Designed with no holes to keep out pests, beveled edges to minimize damage potential from turf equipment, and for easy hand and shovel access  
    Flexible Installations – Interlocking stacking capabilities, extension models and pipe hole knockouts support deeper and flexible installations    
    Environmentally Friendly – Earth‑friendly, LEED-compliant material made of 100% recycled materials (black boxes and black lids only)

    Model Listing

    7 Inch Round Valve Box

  • VB7RND: 7" Round Body & Green Lid  
  • VB7RNDB: 7" Round Body Only  
  • VB7RNDBKL: Black Lid  
  • VB7RNDGL: Green Lid  
  • VB7RNDPL: Purple Lid

    • 10 Inch Round Valve Box

  • VB10RND: 10" Round Body & Green Lid  
  • VB10RNDB: 10" Round Body Only  
  • VB10RNDL: Green Lid  
  • VB10RNDPL: Purple Lid  
  • VB10RNDBKL: Black Lid  
  • VB10RNDH: 10" Round Body & Locking Green Lid

    • Standard Valve Box

  • VBSTD: Standard Body & Green Lid  
  • VBSTDB: Standard Body Only  
  • VBSTDBKL: Black Lid 
  • VBSTDPL: Purple Lid  
  • VBSTDH: Standard Body & Locking Green Lid

    • Standard Extension 

  • VBSTD6EXTB: Standard Extension Body Only

    • Jumbo Valve Box 

  • VBJMB: Jumbo Body & Green Lid  
  • VBJMBB: Jumbo Body Only  
  • VBJMBGL: Green Lid  
  • VBJMBPL: Purple Lid  
  • VBJMBBKL: Black Lid  
  • VBJMBH: Jumbo Body & Locking Green Lid

    • Jumbo Extension

  • VBJMB6EXTB: Jumbo Extension Body Only

    • Super Jumbo & Maxi Jumbo Valve Box

  • VBSPRH: Super Jumbo Body & 2 Lock Green Lid  
  • VBMAXH: Maxi Jumbo Body & 2 Lock Green Lid

    • Locking Systems

  • VB-LOCK-H: Hex head 3⁄8" x 2 1⁄4" (1.0 x 5.7 cm) bolt, washer, and clip  
  • VB-LOCK-P: Penta head 3⁄8" x 2 1⁄4" (1.0 x 5.7 cm) bolt, washer, and clip

    • Features

    Light & durable construction  
    Side ridges for additional side wall support    
    Pre-molded pipe slots    
    Bottom flanges to help prevent sinking  
    Four colors: available in green, black, tan and purple  
    Multiple configurations designed to provide tight seals and easy maintenance access  
    Earth‑friendly, LEED-compliant material made of 100% recycled materials (black boxes and black lids only)

    Specifications

    PVB Professional Series 6" Round Valve Box

    PVB6RND: 6" round black body & overlapping green lid
    PVB6RNDP: 6" round black body & overlapping purple lid
    PVB6RNDT: 6" round black body & overlapping tan lid
    PVB6RNDGL: 6" round green lid only

    • Snap-in overlapping lid
    • Skid-resistant texture
    • Body built with three ridges for
    • additional sidewall support
    • Top Opening: 6 1⁄8" diameter
    • Bottom Opening: 8 5⁄8" diameter

    PVB Professional Series 10" Round Valve Box

    PVB10RND: 10" round black body & overlapping green lid
    PVB10RNDP: 10" round purple body & overlapping purple lid
    PVB10RNDT: 10" round tan body & overlapping tan lid
    PVB10RNDGL: 10" round green lid only

    • Overlapping lid with bolt hole and twist lock
    • Skid-resistant lid texture
    • Body built with double ridges for
    • additional sidewall support
    • Top Opening: 10" diameter
    • Bottom Opening: 12 13⁄16" diameter

    PVB Professional Series Mini Standard Valve Box

    PVBMST: 10" mini-standard black body & drop-in green lid

    • Our compact alternative to a standard size box
    • Drop-in lid
    • Skid-resistant lid texture
    • Top Opening: 15" L x 9 ½" W
    • Bottom Opening: 18" L x 12 ½" W x 10" H

    PVB Professional Series Standard Valve Box

    PVBSTD: 12" standard black body & drop-in green lid
    PVBSTDP: 12" standard purple body & drop-in purple lid
    PVBSTDT: 12" standard tan body & drop-in tan lid
    PVBSTDGL: 12" standard green lid only

    • Drop-in lockable lid
    • Skid-resistant lid texture
    • Double ledge lid support
    • Ridge adds additional support to sidewalls
    • Top Opening: 18 ¼" L x 13" W
    • Bottom Opening: 21 ¼" L x 15 15⁄16" W x 12" H

    PVBSTD-EXT: Standard Extension

    PVBSTDEXT: 6" black body & overlapping green lid
    PVBSTDEXTT: 6" tan body & overlapping tan lid

    • Overlapping lockable lid
    • Skid-resistant lid texture
    • Body can be used to extent the PVB Standard series
    • Body can be used as a 6" deep box
    • Top Opening: 17" L x 11 ¾" W
    • Bottom Opening: 18 7⁄8" L x 13 5⁄8" W x 6 ¾" H

    PVBJMB: Jumbo Valve Box

    PVBJMB: 12" black body & drop-in green lid
    PVBJMBP: 12" purple body & drop-in purple lid
    PVBJMBT: 12" tan body & drop-in tan lid
    PVBJMBGL: 12" jumbo green lid only

    • Drop-in lockable lid
    • Skid-resistant lid texture
    • Double ledge lid support
    • Ridge adds additional support to sidewalls
    • Top Opening: 22 ¼" L x 16 3⁄8" W
    • Bottom Opening: 25 ¼" L x 19 3⁄8" W x 12" H

    PVBJMB-EXT: Jumbo Extension

    PVBJMBEXT: 6" black body & overlapping green lid
    PVBJMBEXTP: 6" purple body & overlapping purple lid
    PVBJMBEXTT: 6" tan body & overlapping tan lid

    • Overlapping lockable lid
    • Skid-resistant lid texture
    • Body can be used to extent the PVB Jumbo series
    • Body can be used as a 6" deep box
    • Top Opening: 21 3⁄8" L x 15 7⁄8" W
    • Bottom Opening: 22 15⁄16" L x 16 3⁄8" W x 6 5⁄8" H6"

    6" Round Lids

    PVB6RNDGL: 6" round green lid

    10" Round Lids

    PVB10RNDGL: 10" round green lid

    12" Standard Lids

    PVBSTDGL: 12" standard green lid

    12" Jumbo Lids

    PVBJMBGL: 12" jumbo green lid

     

    Dimensions

    6" Round Valve Box - Top Opening: 6 1⁄8" diameter. Bottom Opening: 8 5⁄8" diameter
    10" Round Valve Box -  Top Opening: 10" diameter.  Bottom Opening: 12 13⁄16" diameter
    Mini Standard Valve Box - Top Opening: 15" L x 9 ½" W. Bottom Opening: 18" L x 12 ½" W x 10" H
    Standard Valve Box - Top Opening: 18 ¼" L x 13" W.  Bottom Opening: 21 ¼" L x 15 15⁄16" W x 12" H
    Standard Extension - Top Opening: 17" L x 11 ¾" W.  Bottom Opening: 18 7⁄8" L x 13 5⁄8" W x 6 ¾" H
    Jumbo Valve Box - Top Opening: 22 ¼" L x 16 3⁄8" W.  Bottom Opening: 25 ¼" L x 19 3⁄8" W x 12" H
    Jumbo Extension - Top Opening: 21 3⁄8" L x 15 7⁄8" W.  Bottom Opening: 22 1⁄16" L x 16 3⁄8" W x 6 5⁄8" H

    Model Listing

    6" Round Valve Box

  • PVB6RND: 6" round black body & overlapping green lid

    • 10" Round Valve Box

  • PVB10RND: 10" round black body & overlapping green lid

    • Mini Standard Valve Box

  • PVBMST: 10" ministandard black body & drop-in green lid

    • Standard Valve Box

  • PVBSTD: 12" standard black body & drop-in green lid  
  • PVBSTDP: 12" standard purple body & drop-in purple lid

    • Standard Extension

  • STDEXT: Can be used to extend the Standard Valve box by 6” in height or as a 6” deep box to reduce digging
  • PVBSTDEXT: 6" black body & overlapping green lid  
  • PVBSTDEXTT: 6" tan body & overlapping tan lid

    • Jumbo Valve Box

  • PVBJMB: 12" black body & drop-in green lid  
  • PVBJMBP: 12" purple body & drop-in purple lid

    • Jumbo Extension

  • PVBJMBEXT: 6" black body & overlapping green lid

    • Features

    Proven impact drive with straight-through flow for superior performance in dirty water
    Double-weighted arm for slower rotation and increased distance of throw
    Adjustable arm spring for low-pressure and low-gallonage operation
    Precision Jet tube (PJ™) minimizes side splash
    5 Matched Precipitation Rate (MPR) nozzles and 2 low-angle (LA) nozzles
    Interchangeable, color-coded bayonet mount nozzles
    No tools required to change nozzles
    FP trip permits full circle (360°) or part-circle operation (20° to 340°)
    Powerful reverse action
    Three-year trade warranty

    Specifications

    Precipitation Rate: 0.28 to 1.21 inches per hour (7 to 31 mm/h)
    Radius: 22 to 45 feet (6,7 to 13,7 m)
    Radius with Radius Reduction Screw: 18 feet (5,4 m)
    Pressure: 25 to 60 psi (1,7 to 4,1 Bars)
    Flow Rate: 1.5 to 8.4 GPM (0,34 to 1,91 m3/h; 0,09 to 0,53 l/s)
    Low angle (LA) nozzles: 07 LA-black; 10 LA-yellow
    ½" (15/21) male threaded inlet
    Standard trajectory angle nozzles: 06-red; 07-black; 08-blue; 10-yellow; 12-beige
    Nozzle outlet trajectory is 23° for 06, 07, 08, 10, and 12 nozzles
    LA nozzle outlet trajectory is 11°

    Model Listing

  • 2045-PJ: Maxi-Bird

    • Copyright © 2026 Rain Bird Corporation. All rights reserved.