You Are Here: Homeowners > Products > Valves > DV/DVF Series

DV/DVF Series

Plastic Residential Irrigation Valves

Rain Bird manufactures only the highest quality valves. Use DV/DVF series valves in locations where the use of a separate pressure vacuum breaker (PVB) or a double-check valve is required by city codes to protect against back flow. Check your local city codes to determine what type of valves are required.

All of our residential valves work with any standard sprinkler timer. (Note: not recommended for use with 2-wire systems).

 

 

 

  • Double-filtered (diaphragm and solenoid) pilot-flow design for
    maximum reliability and grit resistance
  • Buna-N, balanced pressure diaphragm with self-cleaning 90 mesh
    (200 micron) pilot water filter and captive spring
  • Energy-efficient, low-power encapsulated solenoid with captured
    plunger and 90-mesh (200 micron) solenoid filter
  • Unique, easy-to-turn patented pressure assisted flow control
    mechanism (DVF models only)
  • External bleed to manually flush system of dirt and debris during
    installation and system start-up
  • Internal bleed for spray-free manual operation
  • Accepts Rain Bird TBOS latching solenoid for use with most battery-operated controllers
  • Operates in low-flow and Landscape Drip applications when a 200
    mesh filter is installed upstream
  • Not recommended for use with two-wire control systems
  • Available as:
    • 3/4" (20/27) and 1" (26/34) standard in-line configuration.
    • 1" (26/34) Slip-by-Slip (SS) configuration for low cost, solvent-weld installations.
    • 1" (26/34) Angle (A) configurations for flexible installations especially when submains are deep.
    • 1" (26/34) Male-by-Male (MM) thread configuration for quick and easy manifolding.
    • 1" (26/34) Male-by-Barb (MB) male thread inlet by barb outlet configuration for installation with poly pipe.
  • Unique, easy-to-turn patented pressure assisted flow control mechanism (DVF models only).


075-DV
3/4" (20/27)


100-DV
1" (26/34)*

   


100-DV-SS
1" (26/34)



100-DV-A
1" (26/34)


   


100-DV-MB
1" (26/34)



100-DVF
1" (26/34)


   


100-DVF-SS
1" (26/34)



100-DVF-MB
1" (26/34)


   

*Available with BSP threads.

  1. Rain Bird recommends flow rates that result in discharge velocities in the supply line not to exceed 7.5 ft/sec (2.3 m/s) in order to reduce the effects of water hammer.
  2. Rain Bird residential valves cannot be used with PRS pressure regulating modules.
  3. Not recommended for use with two-wire systems.

 

  • Pressure: 15 to 150 psi (1,0 to 10,4 bar)
  • 075-DV Flow: 0.2 to 22 GPM (0,05 to 5,0 m3/h; 0,01 to 1,39 l/s). For flows below 3 GPM (0,75 m3/h; 0,21 l/s) or any Xerigation® application, use a 200 mesh filter installed upstream.
  • 100-DV Flow): 0.2 to 40 GPM (0,05 to 9,08 m3/h; 0,01 to 2,52 l/s). For flows below 3 GPM (0,75 m3/h; 0,21 l/s) or any Xerigation® application, use a 200 mesh filter installed upstream.
  • 100-DVF Flow (non-union): 0.2 to 40 gpm (0,75 m3/h; 0,21 l/s); for flows below 3 gpm or any Xerigation application, use a 200 mesh filter installed upstream.
  • Water temperature: Up to 110° F (43° C)
  • Ambient air temperature: Up to 125° F (52° C)
  • 24 VAC 50/60 Hz (cycles per second) solenoid power requirement:
    • 0.450 A inrush current; 0.25 A holding current
  • Solenoid coil resistance: 38 Ohms

Dimensions:

  • Height: 4 1/2" (11,4 cm)
  • Height (Angle): 5 1/2" (14 cm)
  • Width: 3 1/3" (8,4 cm)
  • Length: 4 3/8" (11,1 cm)
  • Length (Angle): 3 3/4" (9,5 cm)
  • Length (MM): 5 3/8" (13,6 cm)
  • Length (MB): 5 3/4" (14,6 cm)